Thread: WSTO 135i V1.2
View Single Post
      12-02-2009, 01:20 AM   #1
Ryan@IND
 
Ryan@IND's Avatar
 
Drives: M3
Join Date: Mar 2008
Location: Chicago

Posts: 4,263
iTrader: (16)

Send a message via AIM to Ryan@IND Send a message via Skype™ to Ryan@IND
WSTO 135i V1.2

As featured on 1addicts Homepage.



Last June we revealed our very own Project 1 (v1.2). It was wearing an array of parts that suited the 135i well. We received many compliments on what we had done, however we were not finished.

Our attention first went to the rear of the car. Bastuck had released a prototype US-spec quad exhaust system for the 135i. We still call it prototype as we feel the fitment is a little off for the US Spec cars with the charcoal canister. We did a little customization on our end to make the fit flawless and look like it was built in Bavaria. We are working with Bastuck to remedy the situation. The quad system just like the dual is a full cat-back system (aft of secondary cats) and utilizes Bastuck‘s own non resonated y-pipe. We opted for the non-resonated version for 2 reasons; less restriction and so we could hear the engine sing. This exhaust really lets the turbo engine sound come through. Slightly more rumble, a bit louder, and a little more "open sound" made for music to our ears.



This time around, we wrapped the 4 huge double walled 85mm Bastuck tips with 3D Design's Carbon Fiber Diffuser. This is a 100% carbon fiber diffuser beautifully crafted in Japan. The 3D Design diffuser integrated seamlessly into the existing lines of the 1er while accentuating the aggressiveness of the car with its center mesh opening and slightly flared openings for the quad exhaust tips. Installation was simple, utilizing all the stock clips and attachment points as well as stock screws on the bottom. Fitment with the OEM bumper and larger Bastuck tips was next to perfect.



Of course, being WheelSTO we could not overlook the wheels. We feel as though wheels will either make or break a car. Although the design of the wheel plays a major role, it is not just one factor but a combination of design, offset, color, drop in height and even the rubber that defines the overall feel and look of the car. For months we have been debating what wheels to go with after we decided to bid farewell to our 3pc Klassen wheels. The Klassen wheels were a thing of beauty with smoked lips and sophisticated liquid metal color and 3pc design, but we knew it was time to carry on the aggressive racy theme of the quad exhaust.

We had always been infatuated with Yokohama Advan's design styles, and build quality. We even thought about trying to fit the aggressive sizing Advan RS (fitment meant for the E90 3 series). I am sure that we could have pulled it off with some fender rolling and camber adjustment and Frank (our resident drifter would have loved it too). Too bad for Frank, Advan released news of the Advan RZ for BMW fitments and even better, an E82 specific fitment. We jumped on the opportunity by calling our Yokohama distributor to pre order a couple of sets.



The sizing that was released was 19x8 +45 and 19x9 +50 and we opted for the Gunmetal finish to complete the dark menacing look. We wrapped them in Yokohama Advan AD08, 225/35/19 and 255/30/19. These tires perform incredibly when carving through corners and look great when parked. They run slightly wider than most other major brands and therefore we did encounter some rubbing with our aggressive drop on H&R Sport Springs. With a slightly narrower tire design (perhaps Falken or Toyo), this setup should be a perfect no rubbing solution. Either way, the car felt great and the rubbing was minimal.



Our 1er (version 1.1) grabbed a lot of attention with the matte black vinyl work we had done on the door panels. Whereas this door panel with huge “WSTO” on the side worked very well for us “commercially”, we wanted a more subtle design that will be the envy of other BMW enthusiasts. The vinyl scheme was stripped but we decided to keep the matte black. Only this time, we added two stripes stretching from the headlights all the way back to the tail lights for a subtle street look. We think that this was an especially nice design by our resident designer/photographer, Johan.




Johan really outdid himself again (he never fails to surprise) and took some amazing pictures of our completed transformation.









WSTO is proud to present you with video of our Project 1 v.1.2

We decided to launch a video in addition to the numerous photoshoot to try and truly capture the essence of what WSTO has been trying to do with the 135i.

Our goal for the video was to show the potential of not only the 1 series, but any other car and show that with passion and creativity and of course a mix of the right modifications, you can truly achieve your dream ride, which would be totally unique to you.

The focus was also on making sure that all components used to build the project 1 are off-the-shelf, bolt-on items that can easily be acquired and put on by anyone.

Your imagination is truly your limit when it comes to modding your cars and in today's tuning world, you can get an array of products that will not only make your car faster, but look different and unqiue.

Lastly, we truly believe that modding should be about you and not about what others say it is and that it should be fun.

We really had fun with this video and hope you enjoy it too.

Plugs (because these guys made it happen):
K1 Productions
IND / A&L
VS Motorsports
3D Design Japan
Mackin Industries (Yokohama Wheels)
Bastuck & Co. GmbH


Last edited by Ryan@IND; 12-04-2009 at 04:02 PM.
Ryan@IND is offline   United_States
0
Reply With Quote