|
|
|
12-03-2011, 03:12 AM | #23 |
teh porcupine
96
Rep 1,726
Posts
Drives: 2020 Tesla 3 LR AWD
Join Date: May 2011
Location: penthouse
|
|
Appreciate
0
|
12-05-2011, 07:17 AM | #24 | |
Major
137
Rep 1,450
Posts |
Quote:
It didn't take long to fit but to be honest, if you glue it on rather than used 3M double sided tape, I recon you could get a better fit to the glass. Once the tape grabs there's not much you can do about repositioning it. I used black silicone sealant around the edge to give a better finish as I didn't like seeing a gap. The sealant wasn't "free flowing" so I had to smooth it myself but unless you get up close like in the pics you wouldn't know. Yes it's the Raze one
__________________
M240i LCI (Mineral Grey):- M2 Door Mirrors, M2 Black Kidney Grills, Lower grille inserts, MP Exhaust, Dinan Carbon Fibre CAI, hot climate intake elbow
|
|
Appreciate
0
|
12-05-2011, 02:54 PM | #25 | |
Brigadier General
138
Rep 4,053
Posts |
Quote:
|
|
Appreciate
0
|
12-06-2011, 06:50 AM | #27 |
Major
137
Rep 1,450
Posts |
Thanks, I'm happy with it and it was easy to fit
__________________
M240i LCI (Mineral Grey):- M2 Door Mirrors, M2 Black Kidney Grills, Lower grille inserts, MP Exhaust, Dinan Carbon Fibre CAI, hot climate intake elbow
|
Appreciate
0
|
12-06-2011, 06:50 AM | #28 |
Major
137
Rep 1,450
Posts |
__________________
M240i LCI (Mineral Grey):- M2 Door Mirrors, M2 Black Kidney Grills, Lower grille inserts, MP Exhaust, Dinan Carbon Fibre CAI, hot climate intake elbow
|
Appreciate
0
|
12-06-2011, 10:53 AM | #29 |
teh porcupine
96
Rep 1,726
Posts
Drives: 2020 Tesla 3 LR AWD
Join Date: May 2011
Location: penthouse
|
so about those full car shots from a few angles...
|
Appreciate
0
|
12-07-2011, 01:50 AM | #31 |
Major
137
Rep 1,450
Posts |
Thats why I would suggest using a glue rather than double sided 3M as the tape grabs and its on. If you used a glue you could press the middle in and it will conform better to the window shape. Unless you are p real close it doesn't show anyway so I am not going to remove it and re fit, hence the black silicone to seal water out from the 3M tape and help to finish it off a little better rather than a small gap in the center of the window.
__________________
M240i LCI (Mineral Grey):- M2 Door Mirrors, M2 Black Kidney Grills, Lower grille inserts, MP Exhaust, Dinan Carbon Fibre CAI, hot climate intake elbow
|
Appreciate
0
|
12-07-2011, 07:15 AM | #32 |
Lieutenant
30
Rep 586
Posts |
try spraying a soapy water mix on the glass this will give you some adjustment time and then hold in place until the 3m starts to stick. Might want to have an extra set of hands or use some duck tape to hold in place.
__________________
2009 135i Black on Black
Options|Leather| Sport Package| Premium Stereo| Steering Assist | V1 Engine MODS| JB4 install | AR DPs | Berk Axleback | ITG Filter | BHS OCC | Exterior Bling| Kerscher splitter | Interior Bling | Bimmian pedals | 3P Cars gauage | |
Appreciate
0
|
12-07-2011, 11:45 AM | #33 |
Major
137
Rep 1,450
Posts |
Thanks for the tip but unless it loosens I think I will leave it be for the time being. I was concerned that using soapy water would affect the bonding properties of the tape and I did not have a helper to hand while I fitted it. Also the temps are too low now for me to redo it so would need to wait till spring/ summer anyway
__________________
M240i LCI (Mineral Grey):- M2 Door Mirrors, M2 Black Kidney Grills, Lower grille inserts, MP Exhaust, Dinan Carbon Fibre CAI, hot climate intake elbow
|
Appreciate
0
|
01-22-2018, 09:40 AM | #35 |
Lieutenant
104
Rep 486
Posts |
http://1m-raze.revozport.com/1mgroof.html
Overpriced in my opinion. That fitment doesn't follow the contour of the roof at all.
__________________
|
Appreciate
0
|
02-18-2018, 05:16 PM | #36 |
Second Lieutenant
20
Rep 202
Posts |
__________________
MODS: JB4 G5 ISO, VRSF V2 3"DPS, N55 mid, ER CP, TIAL BOV, BMS DCI
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|