BMW 1 Series Coupe Forum / 1 Series Convertible Forum (1M / tii / 135i / 128i / Coupe / Cabrio / Hatchback) (BMW E82 E88 128i 130i 135i)
 





 

Post Reply
 
Thread Tools Search this Thread
      03-05-2013, 12:53 PM   #1
TheSt|G
Resident Tamed Racing Driver
TheSt|G's Avatar
United_States
292
Rep
4,697
Posts

Drives: 911, 130is, E39 M5, E36 M3
Join Date: Mar 2008
Location: Outside Philly

iTrader: (2)

DIY Supersprint N52 header install/review

I originally posted this in the 128i engine section, but I figured it would be useful to have around in the DIY section as well for future reference material.


As some of you know I installed SuperSprint headers on my car a few months ago. It was also a bit of fitment R&D as the SuperSprint headers were for the Euro 125i coupe, and it wasn't 100% assured the fitment would be perfect(it was). As far as I know, this is the only 128i Coupe in the US with SuperSprint headers.

I meant to have a thread on the subject up fairly quickly, but recently I have been so busy that it proved impossible. Fortunately, this has given me the ability to record my long term thoughts on the mod, so in the end this is probably the best situation. I also apologize in advance, photos were taken with a phone while working, so they aren't HDR perfection.

This thread will also be a very mild DIY, and I will be happy to give more detailed pointers/help to anyone else attempting this project. That said, since I don't support Chinese junk knockoff headers, I won't provide insight to anyone using MMW headers and the like. Buy from a reputable company like SuperSprint that refuses to export manufacturing and performs proper R&D before any project.


Section 1: The Install

Time:
6 hours at a leisurely pace.

Tools:
Metric socket set
Various length socket extensions
O2 sensor socket
Power driver for time savings
Zip ties
Red Bull

Parts:
Supersprint Headers
Fresh stud locknut hardware
Fresh header to block gaskets
Fresh header to mid pipe hardware

Here is where it all started. In order to proceed you need to remove the cabin air filter cover, cabin air filter, cabin air filter frame, disconnect the wires/enclosure that run above the the valve cover, remove the valve cover, and disconnect a few miscellaneous plugs. In addition, the washer fluid tank mounting bolt needs to be removed so that you can maneuver the washer fluid tank to allow access to the engine block side of the header mounting hardware.




Here is what I installed. I never saw the SuperSprint headers in the raw as I had them shipped directly to Swain Tech for a full ceramic coating. For those who are curious, coatings like this maximize the thermal efficiency of exhaust components and lower overall engine bay temperatures. The net result is a gain in power and reduction in heat soak, both of which seemed highly important to me in a N/A engine that I'm trying to get every ounce of power out of and is built primarily from aluminum and magnesium.




When you finish with the topside disassembly, this is roughly what you should be left with. You may have noticed in this pictures that the precat O2 sensors are mounted on the top of the collector banks, where on the SuperSprint versions they are mounted further down the manifold. More on that later.




At this point you are ready to move under the car. Remove the front underbody panels which should expose where the factory collector track bolts to the factory mid pipe. Also of note in this picture is the anti-vibration bushing fitted to the base of the factory collectors. Seeing as it is connected to the factory pipes, you are unable to reuse it, but I can confidently say in 2 months of usage I haven't heard so much as a peep of a vibration/rattle from the SuperSprint replacements. Also, make sure to wear a sweater while modding, it is cold this time of year.




At this point, alternate from the top and bottom to remove the nuts from the engine block studs on the stock collectors. Some will be at awkward angles and require some ingenuity in terms of arm and body alignment for proper access. Don't worry about dropping/losing them as you should be replacing them with new factory hardware. The nuts are lock nuts and are a one time use item. Once you take them off they are spent and trash. New hardware also only costs a few bucks. When finished, return to the underside of the car and unbolt the headers from the mid pipe, making sure that you disconnected/removed the O2 sensors first. At this point you can feed the stock collectors down and out the bottom of the car, leaving you with this:




At this point I plunked the stock collectors down next to the SuperSprint headers for a photo op. The factory unit, while surprisingly light, still weighs a decent bit more than the SuperSprint version. In terms of equal length piping, there isn't even a shadow of similarity. This is also a good time to fit your new engine block to header gaskets in place on the headers. You need to do a good job of this because if you have a leak you will need to repeat the entire process over again. The fitment is extremely tight on the gaskets, so take your time. Also make sure to transfer the O2 sensors from the factory collectors to your new headers at this point.










After you have fitted the gaskets, you are free to feed the new headers up to the engine block. This takes a bit of time and positioning, but is a pretty easy process. I honestly forget exactly which one goes in first, but I vaguely remember it being one to about a halfway point, and then the other one joining it to go up. After you get them near the block, feed them on to the studs and apply a few new lock nuts to each bank to keep them from falling off. Work your way around and get a lock nut on each stud of the block. Working your way around again, tighten them all down equally in small amounts so that no nut gets far ahead of another in tightness.






With everything tightened down, you should be left with something similar to this. This is also when you need to reroute the wiring from the O2 sensors. Using some of the original factory clips and some other routing, I was able to get them back up to the factory connectors under the valve cover. It is a tight fitment, but it works. I should note that the scuffs you see on the headers are from a bit of the heat shielding rubbing off onto them during the install, not the other way around.



At this point you just need to reassemble everything you took apart from the top and bottom sides of the car.



Section 2: Review

Wow.

I was simply floored at the difference the headers made over stock. I installed them expecting a few HP(SuperSprint is notoriously conservative in their gain estimates) and what I got was a completely transformed car.

Fitment was perfect. I'm used to this from a large amount of experience with other SuperSprint products, but it is the case all over again. Don't expect this with Chinese junk knockoffs, I've seen that pain first hand many times.

In terms of power there are gains across the entire band. Low end torque is vastly improved, mid range power is more insistant, and top range horsepower really pulls the car along now. Throttle response is also vastly improved without feeling jumpy in any way.

In terms of sound the headers would be worth even if they made zero power. On stock pipes aside from the "golf tee" mod the car is perfect. Zero drone inside the car, complete comfort with the windows up, and the sounds of an absolute animal when you get on it. Even low speed driving is a complete blast. Let off the gas from 2500-3500 and the car has a spectacular new burbly overrun. I sadly was unable to capture it on video, but you will find yourself tapping the gas incessantly to trigger it. I welcome any 128i owners who are in my area to swing it for a demo, it is fantastic.

Without further ado, the video, which like all exhaust videos, barely captures how awesome it is:




Dyno:

__________________
2005 E46 M3 Interlagos/Cinnamon with Sunroof Delete
Appreciate 0
      03-05-2013, 12:58 PM   #2
Dackelone
European Editor
Dackelone's Avatar
Germany
10512
Rep
22,992
Posts

Drives: N54 e82
Join Date: Feb 2010
Location: Bayern, Germany

iTrader: (1)

Very NICE!!
Appreciate 0
      03-05-2013, 01:02 PM   #3
TheSt|G
Resident Tamed Racing Driver
TheSt|G's Avatar
United_States
292
Rep
4,697
Posts

Drives: 911, 130is, E39 M5, E36 M3
Join Date: Mar 2008
Location: Outside Philly

iTrader: (2)

Quote:
Originally Posted by Dackelone View Post
Very NICE!!
Completely off topic, but I love your museum guide. Definitely will be incorporated into a future trip.
__________________
2005 E46 M3 Interlagos/Cinnamon with Sunroof Delete
Appreciate 0
      03-05-2013, 01:03 PM   #4
Dackelone
European Editor
Dackelone's Avatar
Germany
10512
Rep
22,992
Posts

Drives: N54 e82
Join Date: Feb 2010
Location: Bayern, Germany

iTrader: (1)

Quote:
Originally Posted by TheSt|G View Post
Completely off topic, but I love your museum guide. Definitely will be incorporated into a future trip.
Thanks!
Appreciate 0
      03-07-2013, 07:42 AM   #5
Bmwbreed
Major
United_States
58
Rep
1,198
Posts

Drives: 2013 BMW 135i
Join Date: Jul 2012
Location: Rota Spain (US Forces)

iTrader: (3)

Sounds great
Appreciate 0
      03-07-2013, 04:28 PM   #6
smellthebeans
Lieutenant Colonel
smellthebeans's Avatar
United_States
87
Rep
1,555
Posts

Drives: LPCs
Join Date: Dec 2006
Location: San Antonio

iTrader: (2)

Garage List
1990 325i  [0.00]
Brilliant!

"The rule of thumb when it comes to emissions systems is that any modification that changes the vehicle from a certified configuration to a non-certified configuration is considered tampering. This applies to both vehicle owners and repair facilities and is therefore a Federal offense."

http://www.drivecleanpa.state.pa.us/...q_customer.pdf

http://www.drivecleanpa.state.pa.us/changes/faq_non.pdf

Other than violating state and federal law and posting the proof on the internet it sounds fantastic.
__________________
Appreciate 0
      03-07-2013, 04:39 PM   #7
Paul@Evolve
Paul@Evolve's Avatar
United Kingdom
73
Rep
176
Posts

Drives: BMWs
Join Date: Feb 2013
Location: Bedfordshire

iTrader: (0)

What a great DIY! Great to hear another happy Supersprint customer
Appreciate 0
      03-07-2013, 05:07 PM   #8
TheSt|G
Resident Tamed Racing Driver
TheSt|G's Avatar
United_States
292
Rep
4,697
Posts

Drives: 911, 130is, E39 M5, E36 M3
Join Date: Mar 2008
Location: Outside Philly

iTrader: (2)

Quote:
Originally Posted by smellthebeans View Post
Brilliant!

"The rule of thumb when it comes to emissions systems is that any modification that changes the vehicle from a certified configuration to a non-certified configuration is considered tampering. This applies to both vehicle owners and repair facilities and is therefore a Federal offense."

http://www.drivecleanpa.state.pa.us/...q_customer.pdf

http://www.drivecleanpa.state.pa.us/changes/faq_non.pdf

Other than violating state and federal law and posting the proof on the internet it sounds fantastic.
Fortunately, no one in the US cares.

Speed limits are at both a State and Federal level as well. Good luck finding anyone who drives at 70 on the highway.

Also, odd place to post that tidbit with half the forum running no cats at all(I still have secondaries).
__________________
2005 E46 M3 Interlagos/Cinnamon with Sunroof Delete
Appreciate 0
      03-08-2013, 08:33 AM   #9
Obioban
Emperor
Obioban's Avatar
1611
Rep
2,753
Posts

Drives: M3, M3, M5, M5
Join Date: Apr 2008
Location: West Chester, PA

iTrader: (0)

Garage List
2008 BMW M5  [0.00]
2017 BMW i3  [0.00]
2005 BMW M3 Coupe  [0.00]
2001 BMW M5  [0.00]
Quote:
Originally Posted by smellthebeans View Post
Brilliant!

"The rule of thumb when it comes to emissions systems is that any modification that changes the vehicle from a certified configuration to a non-certified configuration is considered tampering. This applies to both vehicle owners and repair facilities and is therefore a Federal offense."

http://www.drivecleanpa.state.pa.us/...q_customer.pdf

http://www.drivecleanpa.state.pa.us/changes/faq_non.pdf

Other than violating state and federal law and posting the proof on the internet it sounds fantastic.
lol, really? You felt this worth posting? People install headers and/or delete cats all the time. At least this car still has the secondary cats in place. Further, for all you know this is for off road use only

I'm blown away that someone (you) felt the need to post this.

Better not...
exceed the speed limit
roll through a stop sign
enable halogen highs with xenon highs (as in stock in euro)
tint your front windows a reasonable amount
install OEM blackline tail lights from europe
paint in bumper reflectors (as the european cars come stock)
pass a slow car in the left lane by using the right lane

As those are all illegal as well. Oh noes!
__________________

2005 M3 Coupe, 2004 M3 Wagon, 2001 M5 Sedan, 2008 M5 6MT Sedan, 2012 128i M sport

Last edited by Obioban; 03-08-2013 at 08:46 AM..
Appreciate 0
      01-08-2017, 03:26 PM   #10
Eagle1oh7
Lieutenant Colonel
Eagle1oh7's Avatar
United_States
286
Rep
1,710
Posts

Drives: '11 328i Sedan
Join Date: Oct 2012
Location: Chula Vista CA

iTrader: (0)

Quote:
Originally Posted by TheSt|G View Post
I originally posted this in the 128i engine section, but I figured it would be useful to have around in the DIY section as well for future reference material.


As some of you know I installed SuperSprint headers on my car a few months ago. It was also a bit of fitment R&D as the SuperSprint headers were for the Euro 125i coupe, and it wasn't 100% assured the fitment would be perfect(it was). As far as I know, this is the only 128i Coupe in the US with SuperSprint headers.

I meant to have a thread on the subject up fairly quickly, but recently I have been so busy that it proved impossible. Fortunately, this has given me the ability to record my long term thoughts on the mod, so in the end this is probably the best situation. I also apologize in advance, photos were taken with a phone while working, so they aren't HDR perfection.

This thread will also be a very mild DIY, and I will be happy to give more detailed pointers/help to anyone else attempting this project. That said, since I don't support Chinese junk knockoff headers, I won't provide insight to anyone using MMW headers and the like. Buy from a reputable company like SuperSprint that refuses to export manufacturing and performs proper R&D before any project.


Section 1: The Install

Time:
6 hours at a leisurely pace.

Tools:
Metric socket set
Various length socket extensions
O2 sensor socket
Power driver for time savings
Zip ties
Red Bull

Parts:
Supersprint Headers
Fresh stud locknut hardware
Fresh header to block gaskets
Fresh header to mid pipe hardware

Here is where it all started. In order to proceed you need to remove the cabin air filter cover, cabin air filter, cabin air filter frame, disconnect the wires/enclosure that run above the the valve cover, remove the valve cover, and disconnect a few miscellaneous plugs. In addition, the washer fluid tank mounting bolt needs to be removed so that you can maneuver the washer fluid tank to allow access to the engine block side of the header mounting hardware.




Here is what I installed. I never saw the SuperSprint headers in the raw as I had them shipped directly to Swain Tech for a full ceramic coating. For those who are curious, coatings like this maximize the thermal efficiency of exhaust components and lower overall engine bay temperatures. The net result is a gain in power and reduction in heat soak, both of which seemed highly important to me in a N/A engine that I'm trying to get every ounce of power out of and is built primarily from aluminum and magnesium.




When you finish with the topside disassembly, this is roughly what you should be left with. You may have noticed in this pictures that the precat O2 sensors are mounted on the top of the collector banks, where on the SuperSprint versions they are mounted further down the manifold. More on that later.




At this point you are ready to move under the car. Remove the front underbody panels which should expose where the factory collector track bolts to the factory mid pipe. Also of note in this picture is the anti-vibration bushing fitted to the base of the factory collectors. Seeing as it is connected to the factory pipes, you are unable to reuse it, but I can confidently say in 2 months of usage I haven't heard so much as a peep of a vibration/rattle from the SuperSprint replacements. Also, make sure to wear a sweater while modding, it is cold this time of year.




At this point, alternate from the top and bottom to remove the nuts from the engine block studs on the stock collectors. Some will be at awkward angles and require some ingenuity in terms of arm and body alignment for proper access. Don't worry about dropping/losing them as you should be replacing them with new factory hardware. The nuts are lock nuts and are a one time use item. Once you take them off they are spent and trash. New hardware also only costs a few bucks. When finished, return to the underside of the car and unbolt the headers from the mid pipe, making sure that you disconnected/removed the O2 sensors first. At this point you can feed the stock collectors down and out the bottom of the car, leaving you with this:




At this point I plunked the stock collectors down next to the SuperSprint headers for a photo op. The factory unit, while surprisingly light, still weighs a decent bit more than the SuperSprint version. In terms of equal length piping, there isn't even a shadow of similarity. This is also a good time to fit your new engine block to header gaskets in place on the headers. You need to do a good job of this because if you have a leak you will need to repeat the entire process over again. The fitment is extremely tight on the gaskets, so take your time. Also make sure to transfer the O2 sensors from the factory collectors to your new headers at this point.










After you have fitted the gaskets, you are free to feed the new headers up to the engine block. This takes a bit of time and positioning, but is a pretty easy process. I honestly forget exactly which one goes in first, but I vaguely remember it being one to about a halfway point, and then the other one joining it to go up. After you get them near the block, feed them on to the studs and apply a few new lock nuts to each bank to keep them from falling off. Work your way around and get a lock nut on each stud of the block. Working your way around again, tighten them all down equally in small amounts so that no nut gets far ahead of another in tightness.






With everything tightened down, you should be left with something similar to this. This is also when you need to reroute the wiring from the O2 sensors. Using some of the original factory clips and some other routing, I was able to get them back up to the factory connectors under the valve cover. It is a tight fitment, but it works. I should note that the scuffs you see on the headers are from a bit of the heat shielding rubbing off onto them during the install, not the other way around.



At this point you just need to reassemble everything you took apart from the top and bottom sides of the car.



Section 2: Review

Wow.

I was simply floored at the difference the headers made over stock. I installed them expecting a few HP(SuperSprint is notoriously conservative in their gain estimates) and what I got was a completely transformed car.

Fitment was perfect. I'm used to this from a large amount of experience with other SuperSprint products, but it is the case all over again. Don't expect this with Chinese junk knockoffs, I've seen that pain first hand many times.

In terms of power there are gains across the entire band. Low end torque is vastly improved, mid range power is more insistant, and top range horsepower really pulls the car along now. Throttle response is also vastly improved without feeling jumpy in any way.

In terms of sound the headers would be worth even if they made zero power. On stock pipes aside from the "golf tee" mod the car is perfect. Zero drone inside the car, complete comfort with the windows up, and the sounds of an absolute animal when you get on it. Even low speed driving is a complete blast. Let off the gas from 2500-3500 and the car has a spectacular new burbly overrun. I sadly was unable to capture it on video, but you will find yourself tapping the gas incessantly to trigger it. I welcome any 128i owners who are in my area to swing it for a demo, it is fantastic.

Without further ado, the video, which like all exhaust videos, barely captures how awesome it is:




Dyno:

Hey how did you get the old gasket material off of the block?
__________________
DONE: Seibon CF Hood, M3 Rep, MSport rear w/DD CF Diffuser, M3 Rep Skirts, Seibon CSL trunklid, Forgestar F14 18s w/Michelin PSS, Eisenmann catback, AA Headers, BPC Stage 2, Charcoal Delete+revMotor+AFE Drop In filter
FUTURE MODS: LED headlights, CF rooftop, M3 Suspension Conversion, Dinan CAI Mod
Appreciate 0
      02-03-2017, 04:08 PM   #11
Bubes29
Private
Bubes29's Avatar
United_States
9
Rep
56
Posts

Drives: 2010 128i
Join Date: Mar 2016
Location: Maryland

iTrader: (1)

Did you have to get a tune for the headers?
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 01:10 AM.




1addicts
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST