|
|
|
07-19-2010, 06:23 PM | #1 |
269
Rep 6,093
Posts
Drives: E90 M3
Join Date: Dec 2008
Location: 1460 White Oaks Rd. Suite F Campbell, CA 95008
|
DIY Install Video: BMW Roundel Replacement
Hey guys,
Just thought we'd share this new video of how to properly replace your BMW Roundels. Whether you are replacing a faded, worn out one or simply upgrading to a flashier version....this should be of good help! Special thanks goes out to Justin aka JZIMAGE for making this awesome vid. |
07-22-2010, 09:16 AM | #3 |
Major General
159
Rep 5,689
Posts |
Do you guys have rear ones in cf yet?
__________________
Legal Disclaimer: Anything I or anyone else says about my vehicle on this website(1addicts.com or any affiliated or nonaffiliated sites), pertaining to modifications, is only to gain acceptance from my/our peers, and does not actually represent anything actually existing on my car, and thus, cannot be held against me in any issues, i.e. warranty claims, that may arise.
|
Appreciate
0
|
07-22-2010, 11:57 AM | #4 |
269
Rep 6,093
Posts
Drives: E90 M3
Join Date: Dec 2008
Location: 1460 White Oaks Rd. Suite F Campbell, CA 95008
|
|
Appreciate
0
|
07-25-2010, 12:37 PM | #7 |
Major
42
Rep 1,177
Posts |
kool
__________________
Alpine White, Coral RED , Glacier Silver Aluminum trim, M sport, 6MT, NAV, HiFi, USB-iPod, Bluetooth
Performance: JB4|BMW PE|DP Cosmetics: BMW Sport Pedals|Black Kidney Grill |
Appreciate
0
|
07-25-2010, 03:36 PM | #10 |
Major
1119
Rep 1,407
Posts |
|
Appreciate
0
|
07-28-2010, 02:36 PM | #12 |
NF@ E82
28
Rep 264
Posts |
I would purchase black / white roundels for my 1er if you guys had the whole set available :/
__________________
NF@ Jet Black E82 N54
451Whp/448Wtq @19psi; Pump gas & Meth JB3 12 OHM Tuned by: Terry Burger http://www.youtube.com/user/E82jxk |
Appreciate
0
|
08-05-2010, 06:33 AM | #13 |
Major
1119
Rep 1,407
Posts |
Today I recieved the Suction Cup to remove the BMW roundels from my wheels.
Unfortunately but the system doesn't work because it cannot suck enough. |
Appreciate
0
|
08-05-2010, 11:12 AM | #14 |
Lieutenant General
375
Rep 17,017
Posts |
Hi Pol,
It will take a few tries to get enough suction to pull them out, also make sure to lightly wet the surface of the cup so you get a proper seal. |
Appreciate
0
|
08-06-2010, 03:23 PM | #15 |
Major
1119
Rep 1,407
Posts |
The suction cap doesn't work at all.
I wonder if anyone here can demonstrate the contrary. In my opinion the roundels are too spherical for such a tool and besides, the BMW letters make the surface rough so that it is impossible to draw vacuum. |
Appreciate
0
|
08-06-2010, 03:48 PM | #16 |
269
Rep 6,093
Posts
Drives: E90 M3
Join Date: Dec 2008
Location: 1460 White Oaks Rd. Suite F Campbell, CA 95008
|
Did you try lubricating the surface area slightly with some water? This usually helps create more suction for the tool to be utilized to its full capacity.
|
Appreciate
0
|
08-09-2010, 05:49 AM | #17 |
Major
1119
Rep 1,407
Posts |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|