![]() |
![]() |
![]() |
![]() |
09-21-2014, 04:14 PM | #112 |
European Editor
![]() 10539
Rep 22,992
Posts |
Then you will need a dealer to reset you brake pad light.
__________________
|
Appreciate
0
|
09-21-2014, 05:12 PM | #113 |
Colonel
![]() ![]() 1418
Rep 2,560
Posts
Drives: Rapidly from A to B
Join Date: Jun 2005
Location: Chicago 'burbs or TN Smokies
|
Figured that was my next option. They owe me a free brake fluid change under warranty. Maybe they'll comp me a reset. Will probably bring it in next weekend.
In the meantime I put on some fresh Ferodo 2500s today and bedded them in. Hoping that these tolerate my track activities. |
Appreciate
0
|
10-24-2014, 07:51 PM | #114 |
Enlisted Member
![]() 7
Rep 40
Posts |
Another "thanks" from me!
Just one note, I have read above that some people are still saying they have the red car on lift icon in their dash display, even after shorting out the sensor temporarily. I also had this, but then I turned off the car, back on again, then went back into the reset menu and reset the Inspection (car on lift) setting even though it still said another 11000km to go... and the red icon then went away. Note that my sensors were NOT worn at all. I changed the pads just in time. So my procedure: Swap pads (and rotors in my case) Plug sensor in Start car and reset front brakes (and got the ------- km message and still got inspection warnings) Turn off car Unplug sensor and short out the vehicle side of the sensor with a wire like above Start car and reset front brakes (got 110000km message and still got inspection warnings (as the car knew something wasn't right) Turn off car Plug sensor back in Start car and reset front brakes (got 62000km on the display which sounds better) Turn off car - still got the red car on the lift error/warning Start car and reset the inspection setting. Turn off car - all messages and warnings cleared. Whew! |
Appreciate
0
|
10-26-2014, 05:27 PM | #115 | |
European Editor
![]() 10539
Rep 22,992
Posts |
Quote:
![]()
__________________
|
|
Appreciate
0
|
01-11-2015, 04:04 PM | #116 |
Registered
2
Rep 1
Posts |
I was able to reset the Service Due indicator without a problem, resetting the oil change interval, brake change interval and service due date as well.
Dack, Thanks so much for this!! I did have to have the car running to get into the service reset menu, but then it worked like a charm. Initially, I kept holding it too long and getting into the software/hardware codes section. |
Appreciate
1
|
03-03-2015, 06:16 PM | #118 |
Ex '87 Carrera
![]() 246
Rep 1,259
Posts |
Hmmm... Not working for me for some reason. Trying to reset my oil service due light. I get in, put in key and turn on ignit, then hold trip odom button. After about 7 sec, I do see the yellow triangle with the exclamation mark, but if I release the button, it just goes away again and I don't see the service due. I can get to service due by scrolling to it with the up down button on the stalk, then press BC to enter. I can see the oil change due, but pressing BC again just exits me out to display my mileage, avg speed, etc. so I don't see the 'Reset' choice. Any ideas? THX!
__________________
"I will tell you there is a big difference between driving money and driving blood, sweat and tears." - PorscheGuy79
"I got 328 loaner and was impressed with performance. It feels much faster than my 135i." - MOCKBA |
Appreciate
0
|
03-03-2015, 06:36 PM | #119 | |
European Editor
![]() 10539
Rep 22,992
Posts |
Quote:
Dack
__________________
|
|
Appreciate
0
|
03-04-2015, 10:59 AM | #121 |
Ex '87 Carrera
![]() 246
Rep 1,259
Posts |
Thanks Dack! I dunno what went wrong the first time; it seemed like I went straight from the yellow triangle to the hidden menu and didn't see the service menu. I went out and tried it again (ignit on but engine off) and saw the service menu come up a few secs after the yellow triangle this time, and was able to clear the oil service warning.
I guess the real cause is I'm just a moron... ![]() ianc
__________________
"I will tell you there is a big difference between driving money and driving blood, sweat and tears." - PorscheGuy79
"I got 328 loaner and was impressed with performance. It feels much faster than my 135i." - MOCKBA |
Appreciate
1
|
04-22-2015, 12:54 PM | #122 |
Brigadier General
![]() 368
Rep 3,547
Posts |
I got the "service soon" light and went through all the service intervals to set them well into the future. I don't really use them and my car is out of warranty. But I still had the light. So I hooked up "torque" and looked for errors. I had the dreaded gas cap code (evaporative system warning). I had already got something on the dash that my wife thought was the gas cap so I had tightened it. But the light was on. So I used Torque to reset the error and now the service soon light is out.
On my other cars, I get the check engine light for a evaporative system issue but on my bimmer, it is the service soon light. New one for me. It isn't resettable using this otherwise excellent sticky, however.
__________________
128i Convertible, MT, Alpine White, Black Top, Taupe Leatherette, Walnut, Sport
Ordered 5/22/09, Completed 6/4/09, At Port 6/9/09, On the Georgia Highway 6/13/09, Ship Arrived Charleston 6/24/09 at 10pm, PCD 7/21/09 ![]() |
Appreciate
1
|
04-22-2015, 02:39 PM | #123 | |
European Editor
![]() 10539
Rep 22,992
Posts |
Quote:
Thanks for the great feedback! ![]()
__________________
|
|
Appreciate
0
|
05-01-2015, 03:40 PM | #124 | |
First Lieutenant
![]() ![]() 12
Rep 324
Posts |
Quote:
__________________
LSXOCET - 404rwhp @ 1600 lbs curb weight... bonkers fast
|
|
Appreciate
1
|
07-22-2015, 07:22 PM | #125 |
Lieutenant
![]() ![]() ![]() 223
Rep 542
Posts |
Thanks Dackelone! (funny story, I was at the dealer for something else and asked how much it would cost to reset the light. They told me it would be 140$ to connect my car to their computer to reset the light. I laughed and said no thanks, then they came back to me and said it would be just 70$ for the brake service light... hilarious!)
Hmm which service does that apply to? I just reset my brake service lights for front and rear with -2k overdue on the front and 10k to due in the rear.
__________________
|
Appreciate
1
|
08-03-2015, 04:09 AM | #126 |
Major General
![]() ![]() ![]() 13521
Rep 8,165
Posts |
Discovered the method on Youtube, but it is the same as Dackelone's. Replaced the brake pads and fluid on our E91 last November at home so naturally the brake pad light went on. At our shop they couldn't get rid of it, been like that until now when I discovered this "secret" method. I can't believe I found it out just now LOL. The car's silent now.
![]()
__________________
![]() |
Appreciate
1
|
09-07-2015, 04:40 PM | #127 |
Enlisted Member
![]() 14
Rep 33
Posts |
I planned on changing spark plugs this weekend and wanted to wait until that was done before I reset this, which turned red about a week ago. When I read this post earlier in the morning, I was pissed that I waited! But I tried it anyway and it worked just fine. This is on a 2011 135.
|
Appreciate
1
|
10-07-2015, 12:39 PM | #128 |
Major
![]() ![]() 157
Rep 1,409
Posts |
Found the SI B34 03 13 service bulletin on the BMW TIS entitled, "Incorrect Remaining Service Life from CBS Data for Brake pads".
It applies to E8x,E9X, F2X, F3X chassis ... Situation: The yellow “Service Due” warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The fix is a software update on the "Brake pad correction CBS conversion" module ... After programming, the vehicle CBS data must be corrected. In the diagnostic menu item “Front/rear brake”, select “Reset forecast to 50,000km” and then reset the forecast distance. In the diagnostic menu item “Front/rear brake”, select “Set availability, enter the brake pad thickness” and enter the pad thickness measured in mm. If the service counter increases after entering the actual brake pad thickness, the brake pad thickness must be entered once again. The service counter is now reset to the original value.
__________________
2011 X3 35i with M pack + 2011 135i w/6SPMT | 255 square tire setup | Quaife 3.46 LSD | Diff lock down bracket | Bilstein B8+Swift SpecR springs+H&R FSB | CDV delete | BMS Oil Tstat bypass | ER FMIC & CP | N54Tuning DP | GC Street Camber Plates | M3 FCA +guide rods+RSFB's+Tranny mounts | Manzo toe arms | Cobb Stg2 agressive tune | Hawk DTC70 brake pads | RB SS brake pistons | Goodridge SS brake lines | Custom brake cooling ducts
Last edited by dcaron9999; 10-07-2015 at 12:49 PM.. |
Appreciate
1
|
10-13-2015, 08:08 PM | #129 |
New Member
0
Rep 8
Posts |
where to get this software
Hi,
in one of the posting this thread, someone is using a software. I've attached the photo that he posted. Can someone tell me what software it is and where I can get a copy? Thank you! |
Appreciate
0
|
10-14-2015, 05:53 AM | #130 | |
European Editor
![]() 10539
Rep 22,992
Posts |
Quote:
I posted that screen shot. The software is from Bavarian Technic (BT)... you only pay for the OBDII cable... then download the free sw from their website bellow. Its fairly easy to use. I think "BMwhat" app or "BMW Carly" app also can reset the service interval lights as well. But I have never used those apps before. http://www.bavariantechnic.com/buy.aspx Dackel
__________________
|
|
Appreciate
0
|
10-14-2015, 06:52 AM | #131 | |
New Member
0
Rep 8
Posts |
Quote:
![]() |
|
Appreciate
0
|
10-14-2015, 07:43 AM | #132 |
European Editor
![]() 10539
Rep 22,992
Posts |
Well... most people just buy the basic($179) or enthusiast($287) BT kit. You can find them for sale on 1Addicts from time to time for under $200.
Most apps like Torque or BMwhat or Carly are way cheaper ($5 to $60). Plus you need a OBDII dongle for $30. Dackel
__________________
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|