FS: 1series clear Euro spec Xenon lights *new*

[Louis75th]

Do you think AHL headlight with led brows can be fitted on 2008 135i with AHL and xenon directly?
No coding?

[Jori]

Originally Posted by Louis75th

Do you think AHL headlight with led brows can be fitted on 2008 135i with AHL and xenon directly?
No coding?

Should be the case.

However, when i am able to attach the plugs, i will check that on my own car tomorrow

[CentralPA E82]

Bump for Thomas. I bought a set from him last year, good riddance to the halogens.

[Jori]

Originally Posted by CentralPA E82

Bump for Thomas. I bought a set from him last year, good riddance to the halogens.

THX

[Jori]

[AW128i]

Originally Posted by CentralPA E82

Bump for Thomas. I bought a set from him last year, good riddance to the halogens.

I can't remember, did you end up replacing your NFRM module, too, to get the lights to work?

[Jori]

I will rewire the led brow inside the lights, so they will behave just like the normal lci Xenos.

[Jori]

Originally Posted by Jori

I will rewire the led brow inside the lights, so they will behave just like the normal lci Xenos.

Done and working

[Jori]

Originally Posted by Louis75th

Do you think AHL headlight with led brows can be fitted on 2008 135i with AHL and xenon directly?
No coding?

YES, just tried and it will work 100% by plug'n'play

[CentralPA E82]

To AW: Kept the original FRM, wired a set of capacitors between the harness and the light housing (used 9006 connectors for a clean install). No issues

[Jori]

Originally Posted by CentralPA E82

To AW: Kept the original FRM, wired a set of capacitors between the harness and the light housing (used 9006 connectors for a clean install). No issues

Could you PLEASE explane it more detailled? Would make my life much easier

However, it is also possible to shut the error message down by using BMW EDIABUS software.

[CentralPA E82]

I tried NCS Expert first, unfortunately the FRM would not accept the coding. A new FRM runs $300+ so I wired in a set of capacitors to stop the flickering.

[Jori]

Originally Posted by CentralPA E82

I tried NCS Expert first, unfortunately the FRM would not accept the coding. A new FRM runs $300+ so I wired in a set of capacitors to stop the flickering.

Ok, sounds good so far.
BUT how much Ohm for the capacitors and on witch wires.

PLZ ;-)

[CentralPA E82]

Jori - the easiest way around the frm is to purchase a set of error cancellers and the 9006 connectors from ebay (there are other sources but ebay is the least expensive). I ran a new ground wire on each side from the grounding bolt on the front fenders to the canceller. The positive lead from the harness provides the switched current for the canceller. The other lead from the canceller goes directly to pin 2 (ground) and pin 3 (xenon) of the headlight connection. I used the 9006 connectors to provide a clean installation and allow me to swap out the canceller should it need replacement in the future.

[RedTRex]

Originally Posted by CentralPA E82

Jori - the easiest way around the frm is to purchase a set of error cancellers and the 9006 connectors from ebay (there are other sources but ebay is the least expensive). I ran a new ground wire on each side from the grounding bolt on the front fenders to the canceller. The positive lead from the harness provides the switched current for the canceller. The other lead from the canceller goes directly to pin 2 (ground) and pin 3 (xenon) of the headlight connection. I used the 9006 connectors to provide a clean installation and allow me to swap out the canceller should it need replacement in the future.

This is good, but can you do it "for dummies" ..... what kind of error cancellors and which 9006 connectors. Perhaps a few pics please.

also - What is the FRM if people want to swap it out?

Thanks much!
Rick

[Jori]

@CentralPAE82

Thanks! Yould you post a link for a suitable error canceller?
Would help a lot.

@RedTRex
FRM = Foot Room Module
Sitting in the foot room left and controls the light functions
Costs $300

[ichiban]

do these have similar angel eyes to the 3 or 5 series? I know the older angel eyes (08) were different than the 3s.

[Jori]

You can see the angel eyes on the pictures.

[Jori]

Something like this

http://www.**********s.com/Super-Har...MW-E82-E90.htm

[Jori]

http://www.ebay.com/sch/sis.html?_nk...r+resistor+H11

[SickSixSpd]

R these still available?

[deadmoo]

Are dynamic headlights still available?