|
|
|
11-04-2015, 03:14 PM | #1 |
Captain
152
Rep 984
Posts |
JB4 issue 1st gear boost limiter won't go above 4psi?
Today I played with the JB4's 1st gear boost limiter (speedo menu 13) for the first time and initially set it to 1k RPM which limits boost to 4psi in 1st gear and worked fine. But then when I set it to anything above 1k RPM such as 1.5k (6psi) or 2k (8psi) the boost still limits to just 4psi! I restarted the car and turned the limiter on and off but it still refuses to go above 4psi when I set it on again. Strangely the limiter will do under 4psi though as I saw 2psi when I set it to 500 RPMs so its not stuck just wont do anything above 4psi...anyone had this issue before?
To be clear I can turn the limiter off and hit full boost as normal again, the limiter is just wont go above 4psi when I set it higher than 1k. I'm on map 5 and don't know what version my JB4 is other than I bought it new from Burger in July this year so must be fairly up to date and I assume its a JB5 G5 ISO (but I also noticed today my JB4 speedo menu only goes to 14 instead of 15...so no 3rd gear boost limiter)
__________________
2004E46M36MTCBCinn 'Clubsport'
Last edited by BigRussia; 11-05-2015 at 08:41 PM.. |
11-04-2015, 03:39 PM | #2 |
aiming for 450.....
303
Rep 2,910
Posts |
You need to go over to Burger Tuning's "other" website. You will get your questions answered without any issues.
If you bought the JB4 new, there should have been a paper with website links to get you going.
__________________
Quote from Ezeedee regarding car mods:
"you're only done when you sell the car " |
Appreciate
0
|
11-05-2015, 08:24 AM | #3 |
Lieutenant
29
Rep 414
Posts |
Try switching via laptop
__________________
2008 Aw/Coral Red Manual 135i Coupe-
JB4 G5 + BMS race flash, BMS meth kit, VRSF DP, Big tom Ic, BMS chinese tester CP, Custom Muffler Delete, BMS Oil Cooler Valve, Cowl Filters, Clutch Stop, B&M Short Shifter, Spec Stg 2+ Clutch W/ Oem dmfw, Vmr V710, KW v2, M RSFB, 1M Front and rear Bumper, Performance Side Skirts, slek trunk, Lci blacklines.] |
Appreciate
0
|
11-05-2015, 01:46 PM | #4 | |
Captain
152
Rep 984
Posts |
Quote:
No cable or laptop if I had them I would've been able to say what firmware version my JB4 is in my original post.
__________________
2004E46M36MTCBCinn 'Clubsport'
|
|
Appreciate
0
|
11-05-2015, 03:01 PM | #5 |
Brigadier General
1688
Rep 3,140
Posts
Drives: 2014 M5 6MT
Join Date: Nov 2013
Location: Massachusetts
|
Disconnect the AMP connector from the JB4, wait a minute, and then reinstall the AMP connector on the jb4. Turn the car on and access the menu, select map 5, and ensure all of your boost limiters are disabled. then start the car and test drive it. Sometimes the JB4 needs a hard reset.
__________________
2014 M5 6MT
|
Appreciate
0
|
11-05-2015, 08:35 PM | #6 | |
Captain
152
Rep 984
Posts |
Quote:
And I noticed my post was confusing but I can turn the limiter off and hit normal boost fine, my issue is just with the limiter not going above 4psi at any setting above 1k. Funny thing I'm running map 5 now, wonder if that could be a cause?
__________________
2004E46M36MTCBCinn 'Clubsport'
|
|
Appreciate
0
|
11-06-2015, 09:01 AM | #7 | |
Brigadier General
1688
Rep 3,140
Posts
Drives: 2014 M5 6MT
Join Date: Nov 2013
Location: Massachusetts
|
Quote:
Or you can post your question here in the support section and you'll have ALOT more support since this is BMS's forum. http://www.n54tech.com/forums/
__________________
2014 M5 6MT
Last edited by Solo_M_Tech; 11-06-2015 at 09:25 AM.. |
|
Appreciate
0
|
11-08-2015, 11:32 AM | #8 | |
Captain
152
Rep 984
Posts |
Quote:
__________________
2004E46M36MTCBCinn 'Clubsport'
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|