|
|
|
03-17-2017, 09:55 PM | #23 |
First Lieutenant
24
Rep 370
Posts
Drives: 2011 Jerez Black M3
Join Date: Jan 2013
Location: Los Angeles
|
|
Appreciate
0
|
03-18-2017, 08:11 AM | #24 |
Colonel
1301
Rep 2,093
Posts
Drives: '11 135i M Sport
Join Date: Dec 2013
Location: Delmarva Peninsula
|
You can fit manual boots over the DCT trim if you remove the silver base plate. This is what I did and painted the silver shifter trim black.
__________________
|
Appreciate
1
StephGOD218.50 |
03-18-2017, 08:32 AM | #25 |
Brigadier General
1541
Rep 3,071
Posts |
I checked realoem and the DCT shift know part crosses over to the e89 z4. This company makes an updated shifter for the z4. Not sure it will work but it's worth investigating.
https://jlevisw.com/Accessories-for-...ic-Shift-Knob/ Looks like it's also available from bimmian https://bimmian.com/Accessories-for-...t-Knob/?veh=89
__________________
2011 135i w/ DCT | ZSP Sport Pkg | PPK | Ohlins R
|
Appreciate
0
|
03-19-2017, 01:33 AM | #26 |
Lieutenant
268
Rep 437
Posts |
That more than likely fits the earlier 6 speed automatic (steptronic) cars only. the 7 speed dct and 8 speed auto are already the updated "2014 style shifter". although you likely could do a custom wiring pin-out as long as the dct shaft is the same diameter
|
Appreciate
0
|
04-06-2017, 07:59 PM | #27 |
Second Lieutenant
116
Rep 264
Posts |
I've been wondering if the entire shifter module from an m3 would work properly with some coding... looks similar, and they're about $200 on eBay. They deff have a much more positive "click" while shifting, and look a whole lot better.
|
Appreciate
0
|
07-29-2021, 03:23 AM | #28 |
Private First Class
28
Rep 124
Posts |
I loved the SMG shift knob in my E60 M5 which looks pretty much identical to the ones in E92 M3's but I haven't seen any solutions from reading a number of older posts. Anyone here tried Black Forest with success? https://blackforestindustries.com/co...mw-shift-knobs
|
Appreciate
0
|
09-24-2021, 09:35 AM | #29 | |
Second Lieutenant
145
Rep 219
Posts |
Quote:
|
|
Appreciate
0
|
09-24-2021, 01:53 PM | #30 |
Captain
500
Rep 645
Posts |
No. The wiring is different (but could be retrofitted) and the CAN/LIN messages to/from the transmission are different. You could run M3 software in the DCT, but then you'd either need an M3 rear dif (which would require the whole M3 subframe and custom driveshaft) or get a transmission tune that could change the rear ratio to 3.46.
|
Appreciate
0
|
08-08-2023, 04:24 PM | #31 |
Private First Class
86
Rep 171
Posts
Drives: A4 1.8TQM, 135is DCT
Join Date: Jan 2023
Location: Milwaukee
|
Where did the sport button go?
__________________
2013 BMW 135is Coupe | Dinan Stage 3 | M3 Subframe Bushings | Dinan Monoball Joints | Dinan Toe Links | 1M Strut Bar | MPSS - BMW 313M's 18x7.5 / 18x8.5 | Min Grey, Savanna | Prem, Tech | DCT | #341/586
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|