Just had HPFP replace

joeo · 02-09-2011, 07:57 PM

Just at my HPFP replaced on my 2009 BMW 135i with about 20k miles. One morning it started but the 1/2 engine light came on so I put it back in the garage and called the dealer. They told me to start it again and see if it 'cleared out'. When I started it again, it ran very rough, jerky idle etc. until the service engine soon light came on, then it smoothed out. I didn't drive it, and waited for an appointment.
The part number on the sheet is 13-51-7-613-933 - but that's not that newest pump is it?
Thanks.

-Joe

Cuz5150 · 02-09-2011, 08:12 PM

I would not worry about part #'s. In my humble opinion, they are all the same. Until someone gets a hold of ALL the pumps, "cuts" them open to reveille in inter workings. Everything else is rubbish.

I wouldn't loose sleep over the pumps. BMW is replacing these puppies for the next 12yrs/100,000miles.

Mr C · 02-10-2011, 09:59 AM

Call your SA and ask them if the pump is a 446. That is the pump that works!

joeo · 02-11-2011, 09:36 PM

Talked with the SA and one of the mechanics. They claim that the 933 pump and the 446 are identical. BMW uses the two part numbers to differentiate between recall work (456) and non-recall work (933).

-Joe
My 135i

Prof T · 02-12-2011, 01:19 PM

Thanks, Good info here.

TMR013 · 02-15-2011, 07:16 PM

Just had my recall work done. I got the 446 pump.

I hope to god this one is OK. I didn't have any issues with my original pump after 27K miles. Going to be torqued if all of the sudden I have a failure.

joeo · 02-15-2011, 08:25 PM

Did you have a failure, or did the dealer just do the work?
Thanks

-Joe
My 135i

TMR013 · 02-15-2011, 09:45 PM

Dealer just did the work when I went in for scheduled maintenance. No failure.

02-09-2011, 07:57 PM	#1
joeo Lieutenant 120 Rep 475 Posts Drives: 2009 Crimson Red 135i Join Date: Mar 2008 Location: Sterling, Va iTrader: (0) Garage List 2009 BMM 135i [9.50]	Just had HPFP replace - Right Part Number? Just at my HPFP replaced on my 2009 BMW 135i with about 20k miles. One morning it started but the 1/2 engine light came on so I put it back in the garage and called the dealer. They told me to start it again and see if it 'cleared out'. When I started it again, it ran very rough, jerky idle etc. until the service engine soon light came on, then it smoothed out. I didn't drive it, and waited for an appointment. The part number on the sheet is 13-51-7-613-933 - but that's not that newest pump is it? Thanks. -Joe
	Appreciate 0 Tweet Quote

02-09-2011, 08:12 PM	#2
Cuz5150 Major 215 Rep 1,489 Posts Drives: 06-M3ZHP/04-M3 Vert/02Duc998 Join Date: May 2008 Location: NJ iTrader: (0)	I would not worry about part #'s. In my humble opinion, they are all the same. Until someone gets a hold of ALL the pumps, "cuts" them open to reveille in inter workings. Everything else is rubbish. I wouldn't loose sleep over the pumps. BMW is replacing these puppies for the next 12yrs/100,000miles. __________________ -Diplomacy is saying, "nice doggie while trying to find a rock"- 07-Z4 coupe-Black/Black/6MT/sport/premium/X 04-M3 vert-Black/Imolla/6MT/Cold/Xenon/HK/ 06-M3 Coupe-Mystic/Black/6MT/ZCP/Xenon/HK/ 09-135i- AW/Bk-Lette/6MT/M-pac/Nav/Hi-Fi/Usb-Ipod/SOLD
	Appreciate 0 Quote

02-10-2011, 09:59 AM	#3
Mr C Captain 41 Rep 754 Posts Drives: E92 Dakar and E90 AW Join Date: Aug 2009 Location: SoCal iTrader: (0)	Call your SA and ask them if the pump is a 446. That is the pump that works! __________________ 2011 E90 M3 Alpine White M-DCT 2011 E92 M3 Individual Dakar 6MT
	Appreciate 0 Quote

02-11-2011, 09:36 PM	#4
joeo Lieutenant 120 Rep 475 Posts Drives: 2009 Crimson Red 135i Join Date: Mar 2008 Location: Sterling, Va iTrader: (0) Garage List 2009 BMM 135i [9.50]	Talked with the SA and one of the mechanics. They claim that the 933 pump and the 446 are identical. BMW uses the two part numbers to differentiate between recall work (456) and non-recall work (933). -Joe My 135i
	Appreciate 0 Quote

02-12-2011, 01:19 PM	#5
Prof T COACH 2 Rep 285 Posts Drives: 2010 135 conv, 2009 M3 Join Date: Feb 2011 Location: BMW iTrader: (0)	Thanks, Good info here.
	Appreciate 0 Quote

02-15-2011, 07:16 PM	#6
TMR013 Opus Angelus 425 Rep 1,267 Posts Drives: 2018 LBB M2 Join Date: Apr 2009 Location: Chandler, AZ iTrader: (0)	Just had my recall work done. I got the 446 pump. I hope to god this one is OK. I didn't have any issues with my original pump after 27K miles. Going to be torqued if all of the sudden I have a failure.
	Appreciate 0 Quote

02-15-2011, 08:25 PM	#7
joeo Lieutenant 120 Rep 475 Posts Drives: 2009 Crimson Red 135i Join Date: Mar 2008 Location: Sterling, Va iTrader: (0) Garage List 2009 BMM 135i [9.50]	Did you have a failure, or did the dealer just do the work? Thanks -Joe My 135i
	Appreciate 0 Quote

02-15-2011, 09:45 PM	#8
TMR013 Opus Angelus 425 Rep 1,267 Posts Drives: 2018 LBB M2 Join Date: Apr 2009 Location: Chandler, AZ iTrader: (0)	Dealer just did the work when I went in for scheduled maintenance. No failure.
	Appreciate 0 Quote