BMW 1 Series Coupe Forum / 1 Series Convertible Forum (1M / tii / 135i / 128i / Coupe / Cabrio / Hatchback) (BMW E82 E88 128i 130i 135i)
 





 

Post Reply
 
Thread Tools Search this Thread
      02-08-2013, 10:05 PM   #1
fe1rx
Captain
1390
Rep
776
Posts

Drives: 135i, 328i, Cayman S
Join Date: Jan 2008
Location: Canada

iTrader: (3)

Ground Control Street Camber Plate "Pointers"

As most of you will know, the strut towers have slotted holes to allow for some camber adjustment if the alignment pin is removed from the OE upper strut mount. The alignment pin centers the mount in the slots, meaning that by removing the pin you can get approximately ±0.25 degrees of adjustment from the stock -0.5 degrees.

Name:  1 OE Strut Mount.jpg
Views: 7707
Size:  228.0 KB
OE Strut Mount with Alignment Pin

Ground Control Street camber plates incorporate a stainless steel pointer plate that allows field adjustment to repeatable values. The only problem is that unless the pointer plate is fixed relative to the strut tower, it is free to move within the ±0.25 degree range permitted by the slots in the strut tower – not good for repeatability.

Name:  2 GC Street Plate.jpg
Views: 5147
Size:  139.1 KB
Ground Control Street Camber Plate

Ground Control has thought of that, but they don’t provide any installation instructions so you need to figure out their solution on your own. The pointer plates are “handed” and need to be installed chamfered edge up. They incorporate 10-32UNF tapped holes that permit installation of an alignment pin (not supplied) that bias the pointer plates at the inboard limit of the slotted hole in the strut tower. You just need to find a suitable pin.

A fillister head screw would probably work, but my solution was to enlarge the holes to ¼” and to TIG weld in a stainless ¼” socket head cap screw in the correct hole. The weld must be ground flush on the bottom to prevent it gouging the camber plate.

Name:  3 Modified Pointer Plates.jpg
Views: 4777
Size:  209.5 KB
Modified Pointer Plates

The modified pointer plates bias the plates towards maximum negative camber in the slots.

Name:  4 Modified Pointer Plate Installed.jpg
Views: 7225
Size:  239.7 KB
Pointer Plate biases Camber Plate towards maximum negative camber

With M3 front suspension arms, my front camber is approximately -1.5 degrees with the pointer set to zero on the camber plate.

Name:  5 Camber with plate set to zero.jpg
Views: 5550
Size:  173.6 KB
Camber Plate at zero, M3 Suspension Bits, -1.5° Camber (aprox)

I can adjust the camber plates to a reading of -2 for an actual camber of approximately -3.5 degrees before the upper spring perches (for OE springs) come uncomfortably close to the inside wall of the strut tower.

Name:  6 -2 deg Pointer Setting.jpg
Views: 4566
Size:  185.5 KB
Pointer at -2 degrees


Name:  7 Spring Clearance at -2 deg indicated.jpg
Views: 4443
Size:  271.1 KB
Spring Clearance with pointer at -2 degrees
Appreciate 2
      02-09-2013, 03:48 AM   #2
RimasRS
Colonel
RimasRS's Avatar
85
Rep
2,438
Posts

Drives: BMW X3 SD
Join Date: Sep 2010
Location: Europe

iTrader: (0)

good stuff
Appreciate 0
      02-10-2013, 11:38 AM   #3
bluephobic(1)
Inspiring the youth of tommorow...
United_States
37
Rep
333
Posts

Drives: AllTheTQ's
Join Date: Apr 2010
Location: Ashburn VA

iTrader: (0)

Garage List
2009 135i  [0.00]
I have those :P, GC makes some great parts and they have amazing costumer service no idea why more people dont use there stuff
???
__________________
E82 135i Jet Black over coral red
E39 Dinan 540i manual Topaz blue over beige
F15 X5 35D Mineral white metallic over Mocha Nappa
991.1 911 GT3 Guards red over black alcantara
P13 570GT MSO Volcano Red over saddle tan
Appreciate 0
      02-10-2013, 11:55 AM   #4
Sarge135
Semper FI!
Sarge135's Avatar
United_States
31
Rep
346
Posts

Drives: 2009 135i
Join Date: Nov 2012
Location: Port Saint Lucie, FL

iTrader: (7)

Which one would we have to buy to work with ST/KW coilovers? And will this eliminate the need to use the stock upper of the oe strut?
__________________

2009 SGM 135i M-Sport
Ark l Blackline l iCarbon l AFE l Hawk l VMR l ST Coilover l Parrot Asteroid l JL Audio l Janus-Design l Reiger l BMW Performance l COBB l Evolution Raceworks l TIAL l VRSF
Appreciate 0
      02-10-2013, 03:02 PM   #5
fe1rx
Captain
1390
Rep
776
Posts

Drives: 135i, 328i, Cayman S
Join Date: Jan 2008
Location: Canada

iTrader: (3)

Quote:
Originally Posted by Sarge135 View Post
Which one would we have to buy to work with ST/KW coilovers? And will this eliminate the need to use the stock upper of the oe strut?
This particular plate appears to be best suited to full size springs although the GC website says it is available configured for race springs. Despite the text on the Ground Control website, these plates are not adjustable for caster. They also make a "Hybrid" plate that provides articulation of the spring perch, which would be a better choice for a race spring, in my opinion.

Here is how the "Street" plates work:

The Ground Control Street camber plate uses a large steer bearing and a separate camber bushing. All weight is borne by the steer bearing. The camber bushing allows the strut shaft to articulate and it carries the damping loads. Because the spring perch remains flat relative to the plate and does not articulate with the shaft, this camber plate is best suited to full size OE or Sport lowering springs as opposed to race springs (which are less forgiving of axial misalignment).

Name:  1 Plate on Strut.jpg
Views: 5175
Size:  137.5 KB
Assembled Strut

Name:  2 Plate with Bushing and Upper Steer Bearing Race.jpg
Views: 4681
Size:  208.1 KB
Camber Plate and Upper Steer Bearing Race. Slots allow camber adjustment only.

Name:  3 Steer Bearing.jpg
Views: 5280
Size:  204.6 KB
Spring Perch with Steer Bearing

Name:  4 Spring Perch.jpg
Views: 5043
Size:  171.3 KB
Spring Perch

Name:  5 Bare Plate.jpg
Views: 4552
Size:  188.1 KB
Bare Plate

Name:  6 Camber Bushing Set.jpg
Views: 4580
Size:  230.2 KB
Camber Bushing Parts

Name:  7 Camber Bushing Set Assembled.jpg
Views: 4427
Size:  181.7 KB
Camber Bushing Assembled

Name:  8 Upper Mounting Bolts.jpg
Views: 4614
Size:  154.7 KB
It is necessary to trim one of the upper mounting bolts to clear the strut brace
Appreciate 1
      04-24-2015, 07:51 AM   #6
katsooba
First Lieutenant
katsooba's Avatar
84
Rep
354
Posts

Drives: bmw 135i
Join Date: Apr 2012
Location: Israel

iTrader: (0)

this info is awesome, dont know why there isn't more discussion on this subject,

as to how fits what and such
__________________
135i N55 / KW V3 / MHD Flash / Tons of grip mods / CP-E charge pipe / CP-E 7" FMIC
Appreciate 0
      04-25-2015, 09:37 PM   #7
_Ryan_
Captain
No_Country
59
Rep
741
Posts

Drives: E87 130i
Join Date: Jan 2012
Location: Melbourne, AU

iTrader: (0)

Garage List
2005 BMW 130i  [5.24]
A few things stand out to me:
- Why do they mark numbers on the plate?
- Why don't they fit the pins (or offer them)?
- Have you tried the 1M strut brace ends? They also locate the studs and top plates in a consistent manner, whilst providing better access to the strut top.
Appreciate 0
      04-25-2015, 10:30 PM   #8
Suprgnat
Слава Украине!
Suprgnat's Avatar
Ukraine
2281
Rep
2,425
Posts

Drives: 2013 128i LMB 6MT ZMP Slicktop
Join Date: Jan 2013
Location: California

iTrader: (7)

Garage List
2013 128i  [9.58]
Quote:
Originally Posted by _Ryan_ View Post
- Have you tried the 1M strut brace ends? They also locate the studs and top plates in a consistent manner, whilst providing better access to the strut top.
The 1M strut braces do not locate anything. They are located by the studs in the "guide support" (or the camber plate, or whatever one is using) with their position subject to the stock slotting of the chassis absent the aforementioned alignment pins. They do provide excellent access to the strut tops, though.
Appreciate 0
      04-26-2015, 05:12 AM   #9
_Ryan_
Captain
No_Country
59
Rep
741
Posts

Drives: E87 130i
Join Date: Jan 2012
Location: Melbourne, AU

iTrader: (0)

Garage List
2005 BMW 130i  [5.24]
Quote:
Originally Posted by Suprgnat View Post
The 1M strut braces do not locate anything. They are located by the studs in the "guide support" (or the camber plate, or whatever one is using) with their position subject to the stock slotting of the chassis absent the aforementioned alignment pins. They do provide excellent access to the strut tops, though.
Interesting, so you're suggesting that a closed ring of a mounted part (assuming the firewall end of the brace is torqued to spec) does in fact have movement?
Appreciate 0
      04-26-2015, 08:18 AM   #10
Suprgnat
Слава Украине!
Suprgnat's Avatar
Ukraine
2281
Rep
2,425
Posts

Drives: 2013 128i LMB 6MT ZMP Slicktop
Join Date: Jan 2013
Location: California

iTrader: (7)

Garage List
2013 128i  [9.58]
Quote:
Originally Posted by _Ryan_ View Post
Interesting, so you're suggesting that a closed ring of a mounted part (assuming the firewall end of the brace is torqued to spec) does in fact have movement?
You're right, and I'll qualify my statement.
During the initial assembly of the front suspension the brace assembly would have to be loose to do the alignment and get a consistent zero point for both sides as the braces have no means to locate the strut tops.
Once aligned and torqued, the 1M/M3 braces should be rigid enough to hold things in place while loosening the strut nuts for track side adjustments of the GC camber plates.
Appreciate 0
      04-26-2015, 08:23 AM   #11
_Ryan_
Captain
No_Country
59
Rep
741
Posts

Drives: E87 130i
Join Date: Jan 2012
Location: Melbourne, AU

iTrader: (0)

Garage List
2005 BMW 130i  [5.24]
Quote:
Originally Posted by Suprgnat View Post
You're right, and I'll qualify my statement.
During the initial assembly of the front suspension the brace assembly would have to be loose to do the alignment and get a consistent zero point for both sides as the braces have no means to locate the strut tops.
Once aligned and torqued, the 1M/M3 braces should be rigid enough to hold things in place while loosening the strut nuts for track side adjustments of the GC camber plates.
Thank you, that's how my Vorshlags are setup.

TL;DR
The caveat when using the 1M/M3 brace is that the firewall brace position shouldn't vary between alignments if you rely on assumptions for accurate track side alignments; that said, if you don't have access to the tools or a friendly to weld on pins as per the original post, this may be a viable work around for ~$200 which you can fit yourself with the added benefits of better strut top access.
Appreciate 0
      12-23-2015, 08:17 PM   #12
davidwarren
Captain
davidwarren's Avatar
187
Rep
670
Posts

Drives: 328,325, 325, 335, X5, 640 GC
Join Date: Dec 2011
Location: Louisville, ky

iTrader: (0)

I am so glad I found this. I have GC street plates on my e90. I have been looking for a way to keep the marker plate stationary so only the adjustable part moves.

Looks like I just need to find an appropriate 10-32 screw.
__________________
2010 335i e90 Le Mans Blue/Chestnut Brown | M-Sport | 6MT
Appreciate 0
Post Reply

Bookmarks

Tags
alignment pin, camber plates, ground control

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 11:55 AM.




1addicts
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST