|
|
|
05-24-2013, 10:18 AM | #45 |
Doc Brown
1176
Rep 2,174
Posts |
Got it today, loving it. And while I am certainly very capable of installing this part myself, it seems like some drilling is necessary to get this installed. It does not look like it uses the OEM points, am I correct in this, seeing as the directions are not in English
__________________
|
Appreciate
0
|
05-24-2013, 10:32 AM | #46 | |
Colonel
171
Rep 2,347
Posts |
It's simple
Quote:
__________________
Mods:-Berkexhaust -alpinaB3flash -CobbAP -Cobb FMIC -ER charge pipe tialQ bov -M3 front sway bar -M3 subframe bushings -M3 front upper and lower control arms -M3 guide rods -M3 rear upper control arms -Mfactory LSD -defiv lockdown kit -TC Kline SA coilovers /camber plates- HP rear toe arms |
|
Appreciate
0
|
05-24-2013, 11:27 AM | #48 |
Colonel
171
Rep 2,347
Posts |
I only put one in the middle tabs
Honestly it's overkill with all those screws, bolting the side fins up make it more sturdy then the stock oem one. But it couldn't hurt to throw all the screws on it
__________________
Mods:-Berkexhaust -alpinaB3flash -CobbAP -Cobb FMIC -ER charge pipe tialQ bov -M3 front sway bar -M3 subframe bushings -M3 front upper and lower control arms -M3 guide rods -M3 rear upper control arms -Mfactory LSD -defiv lockdown kit -TC Kline SA coilovers /camber plates- HP rear toe arms |
Appreciate
0
|
05-24-2013, 12:49 PM | #50 |
Lieutenant
28
Rep 408
Posts |
Ah, that's what those pics are showing! I couldn't see the screw in the pic and wondered what they meant, however I did have a bunch of leftover screws and wondered how the top edge was fixed. I'd be very inclined to put some screws in those top tabs, as the tabs don't clip in at all, like the OEM diffuser.
I guess the tabs will need holes to be pilot drilled. |
Appreciate
0
|
05-26-2013, 09:55 AM | #51 |
Lieutenant General ***
61
Rep 751
Posts |
I got mine on Thursday but it's been raining in Boston and I don't have a garage. So hopefully today I get it installed.
|
Appreciate
0
|
05-26-2013, 10:41 AM | #52 |
Semper FI!
32
Rep 346
Posts |
Just ordered a gloss black one from ESE. My car felt naked at Nurotag yesterday. My wallet is hating me,lol.
__________________
2009 SGM 135i M-Sport Ark l Blackline l iCarbon l AFE l Hawk l VMR l ST Coilover l Parrot Asteroid l JL Audio l Janus-Design l Reiger l BMW Performance l COBB l Evolution Raceworks l TIAL l VRSF |
Appreciate
0
|
05-28-2013, 06:54 AM | #54 |
Colonel
171
Rep 2,347
Posts |
Good stuff
__________________
Mods:-Berkexhaust -alpinaB3flash -CobbAP -Cobb FMIC -ER charge pipe tialQ bov -M3 front sway bar -M3 subframe bushings -M3 front upper and lower control arms -M3 guide rods -M3 rear upper control arms -Mfactory LSD -defiv lockdown kit -TC Kline SA coilovers /camber plates- HP rear toe arms |
Appreciate
0
|
05-28-2013, 07:30 AM | #56 | |
Lieutenant
28
Rep 408
Posts |
Quote:
Now waiting for a replacement for the mesh section before I take more pics. I asked for an ABS piece to go in place of the mesh, as I'm not keen on mesh and could see the top of the muffler through it, as well as the red Rieger sticker on the inside of the diffuser. I imagine it would be even worse with the BMWP diffuser, as it has a lot more mesh. As I've been typing this, a package has just arrived from Rieger Tuning! Shame it's hurling down with rain today Will get pics up ASAP - hopefully tomorrow if it stays dry long enough. Last edited by TheRuss; 05-28-2013 at 07:35 AM.. |
|
Appreciate
0
|
05-28-2013, 07:43 AM | #57 |
Semper FI!
32
Rep 346
Posts |
Looks great!
Quote:
__________________
2009 SGM 135i M-Sport Ark l Blackline l iCarbon l AFE l Hawk l VMR l ST Coilover l Parrot Asteroid l JL Audio l Janus-Design l Reiger l BMW Performance l COBB l Evolution Raceworks l TIAL l VRSF |
Appreciate
0
|
05-28-2013, 08:13 AM | #58 |
Lieutenant
28
Rep 408
Posts |
Will get some better pics up tomorrow hopefully, I've not seen it properly in the light myself, as I removed it whilst I was waiting for the new piece.
*Edit: And yes, I know I need darklines! Unfortunately, downpipes are further up my "need" list, so they're next to be done. |
Appreciate
0
|
05-29-2013, 04:25 PM | #60 |
Colonel
171
Rep 2,347
Posts |
The tabs line up on top with out a problem you have to drill the side fins of the diffusor into the inner lip of the bumper it takes 10mins once you bolt the side fins in the thing isn't going anywhere
__________________
Mods:-Berkexhaust -alpinaB3flash -CobbAP -Cobb FMIC -ER charge pipe tialQ bov -M3 front sway bar -M3 subframe bushings -M3 front upper and lower control arms -M3 guide rods -M3 rear upper control arms -Mfactory LSD -defiv lockdown kit -TC Kline SA coilovers /camber plates- HP rear toe arms |
Appreciate
0
|
05-29-2013, 04:27 PM | #61 |
Colonel
171
Rep 2,347
Posts |
Quote:
__________________
Mods:-Berkexhaust -alpinaB3flash -CobbAP -Cobb FMIC -ER charge pipe tialQ bov -M3 front sway bar -M3 subframe bushings -M3 front upper and lower control arms -M3 guide rods -M3 rear upper control arms -Mfactory LSD -defiv lockdown kit -TC Kline SA coilovers /camber plates- HP rear toe arms |
Appreciate
0
|
05-29-2013, 05:33 PM | #63 |
Semper FI!
32
Rep 346
Posts |
My gloss black will be here on Friday!!!
__________________
2009 SGM 135i M-Sport Ark l Blackline l iCarbon l AFE l Hawk l VMR l ST Coilover l Parrot Asteroid l JL Audio l Janus-Design l Reiger l BMW Performance l COBB l Evolution Raceworks l TIAL l VRSF |
Appreciate
0
|
05-29-2013, 05:56 PM | #64 |
First Lieutenant
46
Rep 331
Posts
Drives: M140i F20 LCI-2
Join Date: Jun 2012
Location: Melbourne, Australia
|
That's the best diffuser I've seen by miles. Pity the freight to Australia costs more than the diffuser.
__________________
Current: Alpine White M140i F20 LCI-2, 250kW/335hp, 2018.
Sold: Melbourne Red 340i F30 LCI Luxury Line MMPK - 265kW/355hp, 2016. Sold: Alpine White 123d e82, 2010, 150kW/204hp. |
Appreciate
0
|
05-29-2013, 06:23 PM | #65 |
Lieutenant
33
Rep 566
Posts |
So you HAVE to drill or is just makes it fit even more secure than with the bolts already
__________________
Add1cted
|
Appreciate
0
|
05-29-2013, 06:39 PM | #66 |
Colonel
171
Rep 2,347
Posts |
Yeah
You should drill the side fins in then bolt them up it won't do damage to your bumper and if you go back to stock you won't see any holes
__________________
Mods:-Berkexhaust -alpinaB3flash -CobbAP -Cobb FMIC -ER charge pipe tialQ bov -M3 front sway bar -M3 subframe bushings -M3 front upper and lower control arms -M3 guide rods -M3 rear upper control arms -Mfactory LSD -defiv lockdown kit -TC Kline SA coilovers /camber plates- HP rear toe arms |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|