|
|
|
05-13-2013, 12:10 PM | #23 | |
Lieutenant
37
Rep 499
Posts |
That was the point. lol Quote:
__________________
135i////Cobb Stage 2/VRSF 3" catless DP/BMS intake/BMS OCC/AMS FMIC/CP-e exhaust/19" 8.5 et40 9.5 et45 VMR VB3's BUILD THREAD http://www.1addicts.com/forums/showthread.php?t=832779
|
|
Appreciate
0
|
05-14-2013, 12:55 AM | #25 | |
Brigadier General
127
Rep 3,099
Posts |
Quote:
no nonono no no no no no no take them off it's not worth the headache |
|
Appreciate
0
|
05-14-2013, 12:57 AM | #26 | |
Brigadier General
127
Rep 3,099
Posts |
Quote:
but it's a SERIOUS PITA to peel plasti-dip off wheels, especially one that has hard edges next to curved ones it takes as long to remove as it does to apply finding this out now haha, 2 peeled, 1 half peeled, then i said 'eh later' even with pressure washer help. |
|
Appreciate
0
|
05-14-2013, 07:07 AM | #27 |
Colonel
198
Rep 2,239
Posts |
^^ as long as you do enough coats, it just peels off like electrical tape. You can use a toothpick to lift it up to peel in area's you can't get with your fingers or nails.
__________________
08 e93 335i MT
|
Appreciate
0
|
05-14-2013, 10:04 AM | #28 | |
Lieutenant
37
Rep 499
Posts |
Quote:
Thats very true, the more you apply the more easier it is to remove later on.
__________________
135i////Cobb Stage 2/VRSF 3" catless DP/BMS intake/BMS OCC/AMS FMIC/CP-e exhaust/19" 8.5 et40 9.5 et45 VMR VB3's BUILD THREAD http://www.1addicts.com/forums/showthread.php?t=832779
|
|
Appreciate
0
|
05-14-2013, 10:05 AM | #29 |
Lieutenant
37
Rep 499
Posts |
__________________
135i////Cobb Stage 2/VRSF 3" catless DP/BMS intake/BMS OCC/AMS FMIC/CP-e exhaust/19" 8.5 et40 9.5 et45 VMR VB3's BUILD THREAD http://www.1addicts.com/forums/showthread.php?t=832779
|
Appreciate
0
|
05-14-2013, 10:11 AM | #30 |
Lieutenant
37
Rep 499
Posts |
All you need is this to remove plasti dip/overspray. it comes right off.
__________________
135i////Cobb Stage 2/VRSF 3" catless DP/BMS intake/BMS OCC/AMS FMIC/CP-e exhaust/19" 8.5 et40 9.5 et45 VMR VB3's BUILD THREAD http://www.1addicts.com/forums/showthread.php?t=832779
|
Appreciate
0
|
05-15-2013, 07:13 AM | #32 | |
Brigadier General
127
Rep 3,099
Posts |
Quote:
i sprayed mine on the car, peeled it off on the car... 3/10 would not do again haha ED: mine peels off easily enough once it's going, but it has so many sections it takes a long time overall... (VMR V701's).. and it's near impossible to get off the wheel bolts while on the car (luckily i'm going wheel studs soon lol), or the holes that take the bolts. |
|
Appreciate
0
|
05-15-2013, 12:26 PM | #34 |
Lieutenant
37
Rep 499
Posts |
__________________
135i////Cobb Stage 2/VRSF 3" catless DP/BMS intake/BMS OCC/AMS FMIC/CP-e exhaust/19" 8.5 et40 9.5 et45 VMR VB3's BUILD THREAD http://www.1addicts.com/forums/showthread.php?t=832779
|
Appreciate
0
|
05-23-2013, 06:11 PM | #35 |
Lieutenant
37
Rep 499
Posts |
A lot of people were digging on the yellow rims at AutoX.
__________________
135i////Cobb Stage 2/VRSF 3" catless DP/BMS intake/BMS OCC/AMS FMIC/CP-e exhaust/19" 8.5 et40 9.5 et45 VMR VB3's BUILD THREAD http://www.1addicts.com/forums/showthread.php?t=832779
|
Appreciate
0
|
05-24-2013, 06:55 AM | #36 |
The Only Sane One Here
61
Rep 1,135
Posts |
Looking good! How did they look after? Did they clean up ok?
__________________
2011 135i VERT SGM/SB/MOONLIGHT - ED - with every single friggin' option they offered.
|
Appreciate
0
|
05-24-2013, 10:16 AM | #37 |
Lieutenant
37
Rep 499
Posts |
Thanks man They cleaned up pretty easy.
__________________
135i////Cobb Stage 2/VRSF 3" catless DP/BMS intake/BMS OCC/AMS FMIC/CP-e exhaust/19" 8.5 et40 9.5 et45 VMR VB3's BUILD THREAD http://www.1addicts.com/forums/showthread.php?t=832779
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|