|
|
|
06-30-2009, 01:35 PM | #23 | |
Captain
25
Rep 627
Posts |
Quote:
|
|
Appreciate
0
|
07-01-2009, 09:40 AM | #24 | |
Lieutenant
35
Rep 485
Posts |
Quote:
I know the AC Schnitzer wheels are 8.5" wide ET43 and they fit just about ok in the front. I would love to see a pic of a 1er with these wheels with 19x8.5 ET45 front and rear..... I found a thread here with V713 19x8.5 ET45 fronts which should give you an idea of what they look like fitment wise. I personally would like the same size wheel on the rear as the one in the thread has had major fender work I think. http://www.1addicts.com/forums/showt...highlight=v710 |
|
Appreciate
0
|
07-01-2009, 10:40 PM | #25 | |
E30 Addict
38
Rep 590
Posts |
Quote:
__________________
|
|
Appreciate
0
|
07-03-2009, 03:02 PM | #26 |
Good life
130
Rep 1,937
Posts |
I think I might have to try it out then. What exact specs should I request when ordering? I'm still confused on what numbers work for the 135.
__________________
Current: 08 E90 M3 Alpine White Former: 11 135i Msport Space Gray -Former: 07 335i Titanium Silver E92- Former: 08 135i Alpine White E82- Past: 06 Subaru STI WRB- Past: 04 Audi S4 Imola yellow- Past:97 Honda prelude Ice blue
|
Appreciate
0
|
07-03-2009, 03:04 PM | #27 | |
256
Rep 4,048
Posts |
Quote:
ET35 fronts 18/19x8.5" ET45 rears 18/19x9.5" I would try to stretch that front tire pretty good to make it fit nicely. A 215 size tire should work, but obviously it's just a guessing game. |
|
Appreciate
0
|
07-03-2009, 04:24 PM | #28 |
Captain
25
Rep 627
Posts |
are you sure they dont have ET45 18/19x8.5 front?????? someone on the board have the ET45 I believe....
|
Appreciate
0
|
07-03-2009, 07:11 PM | #29 |
E30 Addict
38
Rep 590
Posts |
According to thier website they have et45 all around
__________________
|
Appreciate
0
|
07-04-2009, 04:15 AM | #30 |
Lieutenant
35
Rep 485
Posts |
I have just been told by a UK supplier that they contacted Velocity Motoring and they have confirmed that the V710 only comes in 8.5 ET35 and not ET45 for BMW fitment.
I think the ET45 as stated in the website is only available for VW/Audi 5x112 fitment. |
Appreciate
0
|
07-04-2009, 11:11 AM | #32 |
Lieutenant
35
Rep 485
Posts |
|
Appreciate
0
|
07-06-2009, 12:41 PM | #33 | |
256
Rep 4,048
Posts |
Quote:
It should be actually 18x8.5" ET40 all around for the CSLs. V713's are NOT available in 19x8.5" ET 45 unless they milled down the offset to that size which is not recommended. That offset should be ET35 for any 8.5" wheel unless you're running it for a E60 or M3 (which is ET25-ET20). |
|
Appreciate
0
|
07-06-2009, 12:54 PM | #34 |
E30 Addict
38
Rep 590
Posts |
I dunno, but when I talked to Ty he said they came in et45, the website says they do, and my invoice also says et45. So are you saying that VMR shaved my wheels?
__________________
|
Appreciate
0
|
07-06-2009, 01:02 PM | #35 | |
256
Rep 4,048
Posts |
Quote:
VMR would never mill down or shave wheels without letting me know, it was my mistake to blabber about those wheels in the wrong offset, but as I just confirmed, for a very short production run, these wheels were made in a ET45 in the 19x8.5" sizing. Sorry about that guys |
|
Appreciate
0
|
07-06-2009, 04:00 PM | #36 |
Lieutenant
35
Rep 485
Posts |
Such a shame they don't do the V710 in ET45 for BMW fitment as they do it in 5x112 Audi/VW fitment!
Here's a thread I found on a couple of Audi forums http://forums.fourtitude.com/zerothread?id=4320740 http://forums.audiworld.com/showthread.php?t=2745850 Perhaps if there is a demand, they may make a limited run at special 1 series offset??? I'd be interested..... Perhaps we can do a group buy assuming Velocity would be interested that is |
Appreciate
0
|
07-15-2009, 11:18 PM | #37 |
Ti Da Juice Mane
8
Rep 48
Posts |
Update...after a long wait and breaking the car in I finally did the install of my wheels. The fronts are fine I have no rubbing. However, the rears def rub but where they are actaully rubbing I beleieve they can fit with with some fender rolling. Pics take from my phone so quality is alright. I will try and get some more pics with my camera later this week. Enjoy
|
Appreciate
0
|
07-16-2009, 12:54 AM | #39 |
aka 1013MM
1249
Rep 9,545
Posts |
monster truckish...
__________________
|
Appreciate
0
|
07-16-2009, 01:33 AM | #40 |
Lieutenant
35
Rep 485
Posts |
These are may favourite wheels, I think they stick out too much for my tastes with those offsets.
I wonder if VMR would make the correct offsets if we do a group buy??? EDIT: Have a look here for possible group buy in 1 Series fitment!!! http://www.1addicts.com/forums/showthread.php?t=282752 Last edited by sootyvrs; 07-16-2009 at 06:59 PM.. |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|