COBB AccessPORT for the 2011 BMW 135, 335i and 335xi - Page 4 - BMW 1 Series Coupe Forum / 1 Series Convertible Forum (1M / tii / 135i / 128i / Coupe / Cabrio / Hatchback) (BMW E82 E88 128i 130i 135i)

Venom · 02-05-2013, 03:40 PM

Quote:

Originally Posted by whostorm05

Thanks Venom. Can you think of a purpose for running both at the same time?

Yes, a piggyback has access to different modules compared to what the flash can access. "The BMS JB4 back end flash transfers fuel control from the JB4 to the DME and adds VANOS tuning, higher than OEM ignition advance, and a host of additional flash map changes"

In other words, BMS uses a different set of variables to modulate power output in comparison to Cobb. I don't remember offhand how they work. The answer should be in this thread: http://www.1addicts.com/forums/showthread.php?t=447410
I wasn't able to find it though. Shame Bryce isn't around anymore, I would have suggested you ask this on that/his thread.

whostorm05 · 02-05-2013, 07:33 PM

Thanks Venom. If I have pretty much full bolt ons (downpipe, exhaust, intake, etc) do you think I'd seen an improvement in going to the JB4 Stage 2 along with the AccessPORT?

Venom · 02-05-2013, 08:52 PM

The rule of thumb I have read is that if you are pushing near 450whp then yes, if not, then you wont see much if any gain.

whostorm05 · 02-06-2013, 10:36 AM

Quote:

Originally Posted by Tricki

Prepared to risk it... 2012 not supported although some work!! Has been shipped out and awaiting for it.. Will let u guys know how it goes.. Worst case it gets sent back, although planning to hold onto it and once supported I will update and hopefully work then !!

Tricki - what was the build date of your car? Let us know how it goes when you try the install.

Twhill19 · 02-06-2013, 01:53 PM

I picked up in may of 2012...any chance I have the 2011 dme? It came into port in may 2012 as well...

Tricki · 02-07-2013, 07:36 AM

Quote:

Originally Posted by whostorm05

Tricki - what was the build date of your car? Let us know how it goes when you try the install.

May 2011 Build... looks to be here either Friday or Monday.... fingers crossed

Sequence · 02-07-2013, 09:47 AM

Quote:

Originally Posted by whostorm05

Thanks Venom. If I have pretty much full bolt ons (downpipe, exhaust, intake, etc) do you think I'd seen an improvement in going to the JB4 Stage 2 along with the AccessPORT?

How long did it take for you to install DP on the N55? If it doesn't take too much time out of a day I may just suck it up and switch back to stock for emissions 1x a year.

Not to thread jack with my above statement, but I ordered my Cobb AP a few days ago. Can't wait to install that bishhhhhh

whostorm05 · 02-07-2013, 03:47 PM

Quote:

Originally Posted by Sequence

How long did it take for you to install DP on the N55? If it doesn't take too much time out of a day I may just suck it up and switch back to stock for emissions 1x a year.

Not to thread jack with my above statement, but I ordered my Cobb AP a few days ago. Can't wait to install that bishhhhhh

Sequence - I bought the car with the downpipe already installed. I know a shop in Cali did it but I'm not sure how long it would take to remove/replace.

Twhill19 · 02-08-2013, 04:35 AM

Quote:

Originally Posted by whostorm05

Quote:

Originally Posted by Sequence

How long did it take for you to install DP on the N55? If it doesn't take too much time out of a day I may just suck it up and switch back to stock for emissions 1x a year.

Not to thread jack with my above statement, but I ordered my Cobb AP a few days ago. Can't wait to install that bishhhhhh

Sequence - I bought the car with the downpipe already installed. I know a shop in Cali did it but I'm not sure how long it would take to remove/replace.

Should be about 1-2 hrs depending on how good you are with mechanical stuff/if you have access to a lift or not

Crumpet · 02-08-2013, 05:08 AM

Quote:

Originally Posted by Tricki

May 2011 Build... looks to be here either Friday or Monday.... fingers crossed

cant wait to hear how it goes

josemh23 · 02-09-2013, 01:21 PM

recently installed on my n55 135 and after updating i cant find the maps on the accessport. i downloaded the maps from the site and when i try to install it says the map does not match the ecu the accesport is installed. should i uninstall??? and where are the maps the accessport came preloaded????????? help...please

Venom · 02-09-2013, 01:27 PM

Quote:

Originally Posted by josemh23

recently installed on my n55 135 and after updating i cant find the maps on the accessport. i downloaded the maps from the site and when i try to install it says the map does not match the ecu the accesport is installed. should i uninstall??? and where are the maps the accessport came preloaded????????? help...please

You need to uninstall. Sounds like your firmware was updated and the one you received isn't supported. What you now need to do is be patient and "I just tried to install my AccessPORT and it is telling me that my vehicle is an "Unsupported ROM Version" and won't let me install, what should I do?
You have encountered an ECU that we have not yet added support for. However, the AccessPORT is able to download your vehicle's ROM which you can email to us and we can then add support. To download your ROM, follow the instructions found here: http://cobbtuning.com/info/?id=5848. Next use AccesPORT Manager to save this file to your computer. Then email the file to rom@cobbtuning.com along with your Name, Email address, Vehicle Year Make and Model and transmission type. Once we have the ROM adding support should only take a few days and we will email you with instructions for adding support to your AccessPORT."
From: http://www.e90post.com/forums/showthread.php?t=472813
I am assuming that your car has been updated by the dealership via a F/W update.

josemh23 · 02-09-2013, 01:39 PM

My mistake . I update the firmware of the accesport not the car. And now I search on the maps files and the maps are locked, only 2 sport and aggressive and the stock and valet are not even on the port

Tricki · 02-11-2013, 03:35 AM

I tried to install and unrecognized ROM, which I expected!! Now I hope cobb can get me going.. I have sent details to them via their website and now wait anxiously !!!

please please please!!

Twhill19 · 02-11-2013, 06:29 AM

Quote:

Originally Posted by Tricki

I tried to install and unrecognized ROM, which I expected!! Now I hope cobb can get me going.. I have sent details to them via their website and now wait anxiously !!!

please please please!!

The leap of faith! If this works you will be an innovator, well done

Artovs · 02-11-2013, 08:05 PM

Interesting update from COBB regarding older unsupported ROM's.

http://www.e90post.com/forums/showth...780709&page=10

Don't brick your cars, people! Check and double check! And then check again.

COBB Tuning · 02-11-2013, 08:15 PM

Quote:

Originally Posted by Artovs

Interesting update from COBB regarding older unsupported ROM's.

http://www.e90post.com/forums/showth...780709&page=10

Don't brick your cars, people! Check and double check! And then check again.

Sorry I missed this thread guys. There is an issue with older roms, however we have released firmware that will allow you to safely uninstall, then go to the dealer to get your DME updated to a newer rom. This is only a possible issue with 9780B roms. We've seen zero issues in the field, but we wanted to be safe for everyone's sake. We sent emails to anyone we had on file with a bad rom and thiere were very few people since this is a very early revision from BMW.

When I released the firmware today, I also added support for everyone that was waiting with a good rom.

The firmware with the changes for the bad rom will be v1.6.7.0-5426 or above. Please let me know if anyone has any concerns or questions.
josh.dankel@cobbtuning.com

-Josh

Tricki · 02-11-2013, 09:02 PM

"Richard,

Good news!

The Accessport firmware with support for your vehicle is ready. Follow the directions below to do an online beta firmware update to add our most recent programming to your Accessport"

I see it but dont beleive it.... Cant wait to get home from work and try this baby out... Im still in dissbelif until its loaded and going!!

COBB Tuning · 02-11-2013, 09:31 PM

Quote:

Originally Posted by Tricki

"Richard,

Good news!

The Accessport firmware with support for your vehicle is ready. Follow the directions below to do an online beta firmware update to add our most recent programming to your Accessport"

I see it but dont beleive it.... Cant wait to get home from work and try this baby out... Im still in dissbelif until its loaded and going!!

Haha, I added your support as soon as I pushed out the new firmware release. Sorry for your wait. Hope you enjoy the new power!

Let me know if you run into any issues.

-Josh

Twhill19 · 02-11-2013, 10:35 PM

Where's my update Cobb?!? '12 DME version N55?

COBB Tuning · 02-11-2013, 10:41 PM

Quote:

Originally Posted by Twhill19

Where's my update Cobb?!? '12 DME version N55?

Have you sent us a rom? Are you just asking for support since you're a 2012?

If you're just looking to see if you're supported due to your model year, send me a PM or email with the last 7 of you vin and I'll see where we're at.

-Josh

Tricki · 02-12-2013, 02:59 AM

Ok Australian N55 135i 2011 owners!!! Success on installing Cobb.. Excited and defiantly less traction on hard acceleration.. Will do some 80-180 acceleration which is where I want the xtra speed !!!
Will keep u posted ...

02-05-2013, 07:33 PM	#68
whostorm05 Second Lieutenant Drives: 2012 135i Join Date: Dec 2011 Location: Indianapolis, IN Posts: 201 iTrader: (0)	Thanks Venom. If I have pretty much full bolt ons (downpipe, exhaust, intake, etc) do you think I'd seen an improvement in going to the JB4 Stage 2 along with the AccessPORT? Last edited by whostorm05; 02-05-2013 at 09:42 PM.

02-05-2013, 08:52 PM	#69
Venom Major Drives: Teg DC2 + E82 135i Join Date: May 2011 Location: Easy Bay, CA Posts: 1,463 iTrader: (3) Garage List 2008 BMW 135i [4.25]	The rule of thumb I have read is that if you are pushing near 450whp then yes, if not, then you wont see much if any gain. __________________ - Thanks MGallop! Widebody 135i Powered by: Wagner-Tuning & VMR Wheels TheSt\|G - "And if you think the 1M got the N54 for any reason other than to keep it slower/cheaper than the M3 you are delusional."

02-09-2013, 01:21 PM	#77
josemh23 Private Drives: 135i Join Date: Jan 2011 Location: PR Posts: 65 iTrader: (0) Garage List 2011 135i [0.00]	cant change maps recently installed on my n55 135 and after updating i cant find the maps on the accessport. i downloaded the maps from the site and when i try to install it says the map does not match the ecu the accesport is installed. should i uninstall??? and where are the maps the accessport came preloaded????????? help...please

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

02-06-2013, 01:53 PM	#71
Twhill19 hungry Drives: 2012 135i N55 Join Date: May 2012 Location: Boston, MA Posts: 443 iTrader: (0)	I picked up in may of 2012...any chance I have the 2011 dme? It came into port in may 2012 as well...

02-09-2013, 01:39 PM	#79
josemh23 Private Drives: 135i Join Date: Jan 2011 Location: PR Posts: 65 iTrader: (0) Garage List 2011 135i [0.00]	My mistake . I update the firmware of the accesport not the car. And now I search on the maps files and the maps are locked, only 2 sport and aggressive and the stock and valet are not even on the port

02-11-2013, 03:35 AM	#80
Tricki Enlisted Member Drives: BMW 135i DCT N55 2011 Join Date: Jun 2012 Location: Melbourne Australia Posts: 46 iTrader: (0)	I tried to install and unrecognized ROM, which I expected!! Now I hope cobb can get me going.. I have sent details to them via their website and now wait anxiously !!! please please please!!

02-11-2013, 08:05 PM	#82
Artovs New Member Drives: 2011 Lemans Blue 135i w/DCT Join Date: Sep 2012 Location: Bay Area Posts: 10 iTrader: (0)	Interesting update from COBB regarding older unsupported ROM's. http://www.e90post.com/forums/showth...780709&page=10 Don't brick your cars, people! Check and double check! And then check again.

02-11-2013, 09:02 PM	#84
Tricki Enlisted Member Drives: BMW 135i DCT N55 2011 Join Date: Jun 2012 Location: Melbourne Australia Posts: 46 iTrader: (0)	"Richard, Good news! The Accessport firmware with support for your vehicle is ready. Follow the directions below to do an online beta firmware update to add our most recent programming to your Accessport" I see it but dont beleive it.... Cant wait to get home from work and try this baby out... Im still in dissbelif until its loaded and going!!

02-11-2013, 10:35 PM	#86
Twhill19 hungry Drives: 2012 135i N55 Join Date: May 2012 Location: Boston, MA Posts: 443 iTrader: (0)	Where's my update Cobb?!? '12 DME version N55?

02-12-2013, 02:59 AM	#88
Tricki Enlisted Member Drives: BMW 135i DCT N55 2011 Join Date: Jun 2012 Location: Melbourne Australia Posts: 46 iTrader: (0)	Ok Australian N55 135i 2011 owners!!! Success on installing Cobb.. Excited and defiantly less traction on hard acceleration.. Will do some 80-180 acceleration which is where I want the xtra speed !!! Will keep u posted ...