|
|
|
05-15-2018, 07:57 AM | #24 |
Registered
0
Rep 3
Posts |
Window error codes - waiting for solution
Hey Guys,
Given an E87, and I've fault in both side front windows. I've checked the error codes, they are Time Windows disturbed 009CC7 and 009CC8 Anyone of You can give me a hint how to solve this problem please? Thank You. I appreciate it! |
Appreciate
0
|
07-19-2018, 10:50 AM | #25 | |
Private First Class
11
Rep 102
Posts |
Quote:
Paul |
|
Appreciate
0
|
05-28-2020, 11:52 AM | #26 | |
Registered
0
Rep 2
Posts |
Quote:
|
|
Appreciate
0
|
03-25-2021, 01:50 PM | #28 |
Brigadier General
836
Rep 3,855
Posts |
Amazing!
Thank you for this post! I freaked when my windows didn't do this anymore after disconnecting the battery. Now it's all good.
|
Appreciate
0
|
12-22-2021, 11:08 PM | #29 |
Private
20
Rep 94
Posts |
Ive tried reseting the limits but it wont take. My issue may be different though, my windows will only go up and down about an inch at a time. Rear windows work fine but both front windows do exactly the same thing and will only move in 1 inch increments.
Any ideas? |
Appreciate
0
|
11-15-2022, 11:11 AM | #31 |
Private First Class
39
Rep 155
Posts |
Issue:
Window will not go up all the way up after opening it all the way down Solution: "- Sit in the car, and put the key in position 1, so you have power to the windows." "- Push, extra click down hold in my case, and hold down the window switch, and keep it held down for 5 seconds after the window is all the way down. This re-sets the memory, telling the motor, in effect, “Remember where we are now? ” "- Roll window back up, and release switch." THANK YOU!! |
Appreciate
0
|
05-04-2023, 05:03 PM | #32 |
Registered
0
Rep 2
Posts |
I know this is an old thread, but I'm having issue too with a 135i Windows.
Driver side, replaced regulator, after taking off motor wire was hanging out of the spool. Now the window master control switch, works the mirror fine but windows both Drivers side and Passengers side is an issue. Passenger side window only goes up an down at an inch or 2 at a time. Drivers side Window works the same way when it works, sometimes though when hitting the toggle switch up or down it doesn't do anything? Like I said before switch works the mirrors fine? So is my issue the motor on that window getting ready to go or is it a failing master control window switch on the drivers side? This is a 2008 135i. Coupe Any help will be appreciated. |
Appreciate
0
|
05-13-2023, 02:16 AM | #34 |
Registered
0
Rep 2
Posts |
It's for people with disabilities, for easier IN/OUT.
|
Appreciate
0
|
05-13-2023, 02:22 AM | #35 |
Registered
0
Rep 2
Posts |
I have almost the same issue... I have changed window lifting motor and harness, and after job, window does not go down 1/4 inch. It looks like it tries to go down, cuz window moves a little, but not 1/4 inch... And i have lost seal on this window as well, when i drive about 70mph, lots of air noise comes inside the cabin...
I have reseted window position as mentioned in this topic, did not help. Any ideas ? |
Appreciate
0
|
Yesterday, 01:51 AM | #36 |
Registered
0
Rep 1
Posts |
Replaced the drivers side window regulator on my 2016 1 series 118i yesterday, doesnt quite go all the way up - it does the whole drip 1/4 inch as normal, but when closed fully its still about 3-5mm short of fully closing into the seal.
Done the whole fully open, press and hold, fully close, press and hold and doesnt seem to do anything. when the window is fully closed i can manually slide the window up with my hands, there still a little room for movement but again still doesnt fully close all the way up into the seal when i open and close the door. The only thing i can think of is taking the door panel off again and disconnect the motor and see if that resets again after reconnecting it??? unless you guys can advise me to try something different? |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|