03-25-2019, 03:22 PM | #90 | |
Private First Class
18
Rep 153
Posts |
Quote:
I ended up ordering a new OEM Dual-Mass Flywheel and after it arrived last week they installed it along with the new clutch and it was a perfect fit. I picked up my car and was able to drive for a few kms home and the difference was amazing. Unfortunately I wasn't able to do a proper test drive because just when I got home I stubbed my foot and ended up with a broken toe and haven't been able to drive since then...it'll be one more week at least before I can drive again. The good news is that the clutch fits!
__________________
Diego RdS - Lima, Perú
2011 /// 1M Coupe - BSM |
|
Appreciate
0
|
03-25-2019, 09:25 PM | #91 | ||
First Lieutenant
58
Rep 381
Posts |
Quote:
Regards |
||
Appreciate
0
|
05-19-2020, 03:37 PM | #92 |
Banned
239
Rep 277
Posts |
Maybe someone here can help me out. With the 550i clutch route with new DMFW and my mechanic says it doesn't fit. He said the clutch doesn't fit properly and is spaced towards the back of the car. The clutch disk does not make contact with the flywheel.
clutch: 21207603248 Flywheel: 21207640733 |
Appreciate
0
|
05-20-2020, 09:28 AM | #93 |
Colonel
2625
Rep 2,819
Posts
Drives: e82 1M, f87 M2cs
Join Date: Nov 2011
Location: Tri-Cities, Washington
|
The clutch part number is correct, but its the wrong flywheel.
1M flywheel part number is 21-20-7-619-659 Maybe they ordered the 550i flywheel? The only 550i part you should use is the clutch itself, everything else is from the 1M. If your original DMFW isn't toast, you may be able to re-use it and complete install.
__________________
1M track toy mods: BMS chargepipe, BMS OCC, ADE FMIC, ADE motor mounts, MadDad/Lightweight Ti exhaust, ADE custom oil thermostat/cooler, custom MHD tune, F10 550i clutch, Ohlins R+T, Vorschlag camber plates, M3 'vert FSB with Turner endlinks, Stoptech Trophy BBK.
|
Appreciate
0
|
05-20-2020, 09:31 AM | #94 |
Colonel
2625
Rep 2,819
Posts
Drives: e82 1M, f87 M2cs
Join Date: Nov 2011
Location: Tri-Cities, Washington
|
Here is a picture of invoice....this is everything I ordered for the job:
__________________
1M track toy mods: BMS chargepipe, BMS OCC, ADE FMIC, ADE motor mounts, MadDad/Lightweight Ti exhaust, ADE custom oil thermostat/cooler, custom MHD tune, F10 550i clutch, Ohlins R+T, Vorschlag camber plates, M3 'vert FSB with Turner endlinks, Stoptech Trophy BBK.
|
Appreciate
0
|
11-07-2023, 08:05 AM | #95 | |
Private First Class
41
Rep 109
Posts |
Quote:
Also would you suggest i get a new slave cylinder ? Last edited by dee0007; 11-07-2023 at 08:50 AM.. |
|
Appreciate
0
|
11-07-2023, 06:19 PM | #96 | |
Lieutenant
340
Rep 468
Posts |
Quote:
Yes, replace the slave cylinder while you're in there, and the pivot pin. |
|
Appreciate
1
ayao651.50 |
Post Reply |
Bookmarks |
|
|