|
|
|
|
Post Reply |
|
Thread Tools | Search this Thread |
03-28-2008, 10:33 AM | #1 |
Car Addict!!
63
Rep 1,303
Posts |
What's Better? Wax with an Orbital Polisher or Wax by Hand?
Is it any better to use an orbital polishing machine, or is it better to wax by hand?
__________________
2008 /// Commemorative /// 6-Speed /// Titanium Silver /// Fully-Loaded /// 135i Convertible |
03-28-2008, 10:45 AM | #2 |
Lieutenant General
2153
Rep 10,176
Posts |
IMO, if you know how to use an orbital, it's better and easier to use. You should still have to do hand application around places where you can't get by machine.
Once I got used to using the porter cable, I found myself doing more frequent waxing too, since it takes less time to do than hand application. So, that's another positive for the orbital. I still do my claying by hand though. I don't trust using the oribital for that. |
Appreciate
0
|
03-28-2008, 11:11 AM | #3 |
Captain
13
Rep 645
Posts |
imo, if you do it correctly orbitals are the way to go. only disadvantage is that, all other things being equal, you use up a bit more wax in the machine due to pad absorption.
|
Appreciate
0
|
03-28-2008, 11:16 AM | #4 |
PCA, BMWCCA
103
Rep 2,058
Posts |
Orbitals for sure. They lay down a very thin layer, which is all you need. Wax sets up faster and comes off far easier. I have both the Griot's (Makita) 6" and 3" orbitals. Best AC powered on the market. Using the correct pad is important too. Wash, clay, polish, wax. Results are stunning!
__________________
'08 Carrera S 6MT Guards Red/Black ext leather, Carbon fiber pkg, sport exh, sport chrono +, PASM, Nav, Bose, 19" forged turbos, red tranny tunnel
'07 MV Agusta F4 1000 R 1+1, Corse Red/Silver, RG3 race pipes and factory race ECU |
Appreciate
0
|
03-28-2008, 11:42 AM | #5 |
Donkey Kong King
90
Rep 1,129
Posts |
I really don't use my Flex to apply wax/sealant. I apply my Zaino by hand. However, I think the biggest benefit of an Orbital polisher is what it can do for your paint prior to applying wax. With the use of some Menzerna Polish, a white polish pad, I can remove ALL swirls from my paint. This is something I could not do with just my hands. This is the real benefit of an orbital polisher.
|
Appreciate
0
|
03-28-2008, 12:13 PM | #6 |
Major
131
Rep 1,101
Posts |
Machine is better. HOWEVER...you can cause major damage very quickly if you do it incorrectly. I saw a hood that got scratched bad by one little piece of grit getting between the polish pad and the paint. It is the way to go but just make sure you are very careful and get lots of good quality polishing bonnets! I have heard really good things (see BALLS above) about Griot's garage wax kits. They have an orbital poilsh/wax kits with detailed instructions that I have my eye on.
|
Appreciate
0
|
03-28-2008, 02:34 PM | #7 | |
Traveler
8
Rep 173
Posts |
Quote:
__________________
135i SGM, Grey w/Grey Poplar interior.
|
|
Appreciate
0
|
03-28-2008, 03:37 PM | #8 |
Major
131
Rep 1,101
Posts |
Sounds like you are smart...not paranoid!
|
Appreciate
0
|
03-28-2008, 05:32 PM | #9 |
Car Addict!!
63
Rep 1,303
Posts |
Sounds like the orbital machine is the way to go. I definately can see the potential for damage if something were to get on the pad and then scratch or grind itself into the car's paint.
I know from an unfortunate experience, however, that a small contaminant can also find its way into a manual pad or rag and then scratch the paint from waxing by hand. You can't be too careful, as I found out. Do all the orbital machines really totally prevent the paint burn or swirls that the circular polishers can cause?
__________________
2008 /// Commemorative /// 6-Speed /// Titanium Silver /// Fully-Loaded /// 135i Convertible |
Appreciate
0
|
03-28-2008, 05:53 PM | #10 |
Major
131
Rep 1,101
Posts |
The other side of the coin...the modern polishes/waxes are very easy to apply and you get good results by hand. I'm sure the opbital is better but if you buy a good wax and use good quality microfibre applicators/buffing cloths you will also be happy. If you take care of the paint from the start it (hopefully) won't end up in bad shape needing lots of buffing/polishing.
|
Appreciate
0
|
03-28-2008, 07:20 PM | #11 |
Gato Grande
7
Rep 180
Posts
Drives: '08 X5 3.0 SI
Join Date: Dec 2007
Location: Deer Park, IL
|
Excellent thread !!!
__________________
John
|
Appreciate
0
|
03-28-2008, 08:43 PM | #12 |
Private First Class
4
Rep 153
Posts |
I have taken great care of my car over the last 3.5 years and 90,000 miles but it still needs a good polish/wax job that no amount of hand work will fix. Nate
|
Appreciate
0
|
03-28-2008, 09:19 PM | #13 |
Major
131
Rep 1,101
Posts |
So doing a good hand clay/polish/wax job won't cut it? You still need to do a good machine buff to get the paint looking really good? I figured that doing it 2-3 times a year by hand might be fine and the buffer might not be needed. Guess I was wrong! Good to know.
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|