135I to 1M bodywork Complete Info w/ PN and pics

[ilikebmxbikes]

Enough people have asked for it so here it is. Venom and I's cars are 99% done and I feel comfortable that this list is complete.

This information couldn't have been completed without Sk8fe, Tony135i, Phil@Reeves BMW, Venom and I's hard work and time. Thanks to everyone who has contributed to this information.

I have the PN's in groups. They are blocked off as I placed the orders for the parts. Do note, you need everything.




51-75-8-051-609 UNDERHOOD SHIELD 1 109.55

51-11-8-057-717 TRIM COVER, BUMP 1 308.53

51-12-8-052-495 BUMPER TRIM PANE 1 334.87

41-35-8-052-625 SIDE PANEL, FRON 1 238.49

41-35-8-052-626 SIDE PANEL, FRON 1 238.49

51-48-8-051-598 HEAT INSULATOR R 1 58.58

51-71-8-051-597 MULTIFUNCTIONAL 1 176.05

18-20-7-798-560 RUBBER MOUNTING 1 26.63




51-11-7-900-764 Grid, Center

51-11-8-051-613 Flap, Towing Eye, P

51-11-8-053-877 Set of Covers

51-77-8-052-517 Supporting Ledge Le

51-77-8-052-518 Supporting Ledge Ri

51-64-8-051-987 Headlight Bracket

51-64-8-051-988 Headlight Bracket

51-74-8-051-605 Air Duct, Engine Oi

51-74-8-051-606 Air Duct, Engine Oi

51-74-8-051-604 Air Duct, Bottom

51-71-8-051-595 Cover, WheelL Housi

51-71-8-051-596 Cover, WheelL Housi

51-71-8-045-553 Cover Left

51-71-8-045-554 Cover Right

51718051591 - Wheel Housing Bottom Left

51718051592 - Wheel Housing Bottom Right

51-13-8-051-601 Chrome Clip, Left

51-13-8-051-602 Chrome Clip, Right

51-77-8-053-879 Rocker Panel Trim

51-77-8-053-880 Rocker Panel Trim

51-13-8-051-817 Left Base

51-13-8-051-818 Right Base

51-75-8-051-609 Underhood shield

61-67-8-051-590 Windshield Cleaning

Rear Bumper Support - These have the exhaust hangers for the 1M exhaust

51128051589 Carrier, bumper rear

51127131741 WASHER-GASKET

Rear Bumper Side Brackets

51128051611 GUIDE LEFT

51128051612 GUIDE RIGHT

M Door Sill - The ones on the car often break during install. New ones should be purchased.

51478045291 M Trim Piece, front left entry

51478045292 M Trim Piece, front right entry


Bumper seals - top

51647134102 - Seal, front panel/cooler at top

51768045445 - Seal, equipment module, front

Charcoal Filter tubes etc.

08 Vent Pipe 16137845193

10 Vent Pipe 16137845195

11 Exhaust steam pipe with dust filter 16137845194

Exhaust Hangars - 1M specific

3X 18207798560

Sideskirt hardware - Bottom - same as 135i, i was just missing a few

2X 07147122913

Battery Cables

61129217036 Battery cable (plus pole)

61127845120 BATTERY CABLE NEGATIVE

61126929715 Positive battery lead

[JDelphiki]

Figured I'd ask before I actually had to put some effort into it lol, what was your total price for all the parts not including labor?

[ilikebmxbikes]

Originally Posted by JDelphiki

Figured I'd ask before I actually had to put some effort into it lol, what was your total price for all the parts not including labor?

Probably $2500-3k

[135Pats]

Originally Posted by ilikebmxbikes

Probably $2500-3k

That's actually not as bad as I would have guessed. Sweet

[Venom]

My name is Venom and I approve of this message.

I would also like to thank Dan@UnitedBMW for giving me the part numbers for the exhaust mod.

Do note that there was some custom work needed for our relay cables. We do not know what P/N that may be for an OEM relay cable.

I would also like to add thanks to David M. of BMW of Concord Collision Center for diligently confirming the parts list and what other parts ended up being needed like the rear bumper caps and the rear bumper support bracket!

[adevangel84]

Very nice... I read both of the builds and it inspired me to do a 1m conversion... Eventually.. lol Mad props to you both and I love the cars!!!

[firokzz]

Originally Posted by ilikebmxbikes

Probably $2500-3k

you are straight up lying right now!!!!!
only $2500-$3000!!!!!!
i thought @venom's costed like $8,000
thats crazy!!!!

if thats all it takes (plus labor) I'm going to start saving ASAP!!!!
technically this is pretty doable!!

[Stohlen]

Originally Posted by firokzz

you are straight up lying right now!!!!!
only $2500-$3000!!!!!!
i thought @venom's costed like $8,000
thats crazy!!!!

if thats all it takes (plus labor) I'm going to start saving ASAP!!!!

It costs $8000 with labor and random other tidbits they opted for. Dont forget wheels and tires.

[firokzz]

Originally Posted by Stohlen

It costs $8000 with labor and random other tidbits they opted for. Dont forget wheels and tires.

oh, so than its back to being no more than a dream :/

[Venom]

yep the 2500-3k does not account for body work, paint, and labor costs; it only accounts for the OEM parts listed here which have gone up a little in price since our purchase. All told, depending on the shop It's between 7k and 10k.

figure new wheels on top of that too because you won't want to run the high offset 1er wheels. I have a couple pictures on my build thread of how funky that looks.

[Malexander]

[QUOTE=
51-75-8-051-609 UNDERHOOD SHIELD 1 109.55

51-11-8-057-717 TRIM COVER, BUMP 1 308.53

51-12-8-052-495 BUMPER TRIM PANE 1 334.87

41-35-8-052-625 SIDE PANEL, FRON 1 238.49

41-35-8-052-626 SIDE PANEL, FRON 1 238.49

51-48-8-051-598 HEAT INSULATOR R 1 58.58

51-71-8-051-597 MULTIFUNCTIONAL 1 176.05

18-20-7-798-560 RUBBER MOUNTING 1 26.63

[/QUOTE]


Is it the price of the parts in the end of the sentence?

Big thanks for doing this along with the other guys! Really inspiring the read about the project. Im tempted to do it myself!

[Curare86]

Originally Posted by Malexander

Is it the price of the parts in the end of the sentence?

Big thanks for doing this along with the other guys! Really inspiring the read about the project. Im tempted to do it myself!

Yes it is

[ilikebmxbikes]

[QUOTE=Malexander]

Originally Posted by
51-75-8-051-609 UNDERHOOD SHIELD 1 109.55

51-11-8-057-717 TRIM COVER, BUMP 1 308.53

51-12-8-052-495 BUMPER TRIM PANE 1 334.87

41-35-8-052-625 SIDE PANEL, FRON 1 238.49

41-35-8-052-626 SIDE PANEL, FRON 1 238.49

51-48-8-051-598 HEAT INSULATOR R 1 58.58

51-71-8-051-597 MULTIFUNCTIONAL 1 176.05

18-20-7-798-560 RUBBER MOUNTING 1 26.63

[/QUOTE

Is it the price of the parts in the end of the sentence?

Big thanks for doing this along with the other guys! Really inspiring the read about the project. Im tempted to do it myself!

Those are the prices 12 months ago. I ordered a new bumper and underbody shield and they were ~$50 more than I originally paid each. I don't know what other prices are affected but I would assume all large bumpers, skirts, etc have gone up.

[scottn2retro]

Hi All -

On our 135i race car, we're moving up in class, so I'm doing kind of 1M front conversion.
https://www.facebook.com/sctsracing/...type=3&theater

So far, I've only used the 1M front bumper, fenders and front fender liners, but we're a race car going to be in prepared class. For a nice street car, I can definitely see wanting to do the rocker panels and rear fender liners. You could easily fab a piece of plastic from the removed fender liners (and use the speed clips) to fill the 2 holes in between the front center undertray and the new 1M front fender liners

[Fifty3bags]

Originally Posted by scottn2retro

Hi All -

On our 135i race car, we're moving up in class, so I'm doing kind of 1M front conversion.
https://www.facebook.com/sctsracing/...type=3&theater

So far, I've only used the 1M front bumper, fenders and front fender liners, but we're a race car going to be in prepared class. For a nice street car, I can definitely see wanting to do the rocker panels and rear fender liners. You could easily fab a piece of plastic from the removed fender liners (and use the speed clips) to fill the 2 holes in between the front center undertray and the new 1M front fender liners

@scottn2retro, Can you get some pictures of where the sideskirt meets the fender, I'd like to see what the width difference looks like.

[ilikebmxbikes]

Originally Posted by Fifty3bags

@scottn2retro, Can you get some pictures of where the sideskirt meets the fender, I'd like to see what the width difference looks like.

These are the best photos I can find of a car with 1M Fenders on a 135i sideskirt. I got these off FB, if i had the owners Bimmerpost account I would link them. if anyone has it, please let me know.

[Fifty3bags]

Updated the prices with what getBMWparts.com has listed:

51-75-8-051-609 UNDERHOOD SHIELD 1 182.45

51-11-8-057-717 TRIM COVER, BUMP 1 380.90

51-12-8-052-495 BUMPER TRIM PANE 1 425.79

41-35-8-052-625 SIDE PANEL, FRON 1 288.78

41-35-8-052-626 SIDE PANEL, FRON 1 288.78

51-48-8-051-598 HEAT INSULATOR R 1 61.17

51-71-8-051-597 MULTIFUNCTIONAL 1 199.74

18-20-7-798-560 RUBBER MOUNTING 1 16.37




51-11-7-900-764 Grid, Center $66.55

51-11-8-051-613 Flap, Towing Eye, P $16.48

51-11-8-053-877 Set of Covers $22.30

51-77-8-052-517 Supporting Ledge Le $39.22

51-77-8-052-518 Supporting Ledge Ri $39.22

51-64-8-051-987 Headlight Bracket $33.36

51-64-8-051-988 Headlight Bracket $33.36

51-74-8-051-605 Air Duct, Engine Oi $24.93

51-74-8-051-606 Air Duct, Engine Oi $24.93

51-74-8-051-604 Air Duct, Bottom $39.04

51-71-8-051-595 Cover, WheelL Housi $58.52

51-71-8-051-596 Cover, WheelL Housi $58.52

51-71-8-045-553 Cover Left $4.62

51-71-8-045-554 Cover Right $4.62

51718051591 - Wheel Housing Bottom Left $42.70

51718051592 - Wheel Housing Bottom Right $42.70

51-13-8-051-601 Chrome Clip, Left $29.47

51-13-8-051-602 Chrome Clip, Right $29.47

51-77-8-053-879 Rocker Panel Trim $163.98

51-77-8-053-880 Rocker Panel Trim $163.98

51-13-8-051-817 Left Base $6.65

51-13-8-051-818 Right Base $6.81

51-75-8-051-609 Underhood shield $182.45

61-67-8-051-590 Windshield Cleaning $134.04

Rear Bumper Support - These have the exhaust hangers for the 1M exhaust

51128051589 Carrier, bumper rear $184.50

51127131741 WASHER-GASKET $1.88

Rear Bumper Side Brackets

51128051611 GUIDE LEFT $24.23

51128051612 GUIDE RIGHT $24.23

M Door Sill - The ones on the car often break during install. New ones should be purchased.

51478045291 M Trim Piece, front left entry $54.30

51478045292 M Trim Piece, front right entry $54.30


Bumper seals - top

51647134102 - Seal, front panel/cooler at top $4.06

51768045445 - Seal, equipment module, front $6.30

Charcoal Filter tubes etc.

08 Vent Pipe 16137845193 $45.70

10 Vent Pipe 16137845195 $34.18

11 Exhaust steam pipe with dust filter 16137845194 $45.70

Exhaust Hangars - 1M specific

3X 18207798560 $16.37

Sideskirt hardware - Bottom - same as 135i, i was just missing a few

2X 07147122913 $0.55

Battery Cables

61129217036 Battery cable (plus pole) $133.66

61127845120 BATTERY CABLE NEGATIVE $25.07

61126929715 Positive battery lead $27.57



Total of all listed= 3827.79




EDIT: After searching the 1M parts I found the quarter panel assembly. It is under the 1 Series M - Base parts, but if going the direction of cutting the flares and having them welded on I would have these parts confirmed as 1M parts from BMW.

41008052627 LEFT REAR SIDE PANEL $613.38
(Performed using adhesive bonding/riveting repair method.)

41008052628 RIGHT REAR SIDE PANE $613.38
(Performed using adhesive bonding/riveting repair method.)

51717166250 COVER, WHEELHOUSING LEFT $57.37

51717166250 COVER, WHEELHOUSING RIGHT $57.37

[Fifty3bags]

Originally Posted by ilikebmxbikes

These are the best photos I can find of a car with 1M Fenders on a 135i sideskirt. I got these off FB, if i had the owners Bimmerpost account I would link them. if anyone has it, please let me know.

I don't know it, but thanks for posting that. Also, if possible I think this thread should be stickied since I see the topic posted quite a bit.

[scottn2retro]

Originally Posted by Fifty3bags

@scottn2retro, Can you get some pictures of where the sideskirt meets the fender, I'd like to see what the width difference looks like.

My facebook album has all these as well as the 1addicts.com race car thread, but I think this is the one you are looking for

[scottn2retro]

Note that for the rear wheels, to get 275x18 tires, Apex race parts makes an 18x9.5 et62 (that's right, 62mm offset) wheel to stuff into the OEM 135 rear fenders without doing that part of the conversion.

[Ingeniator]

Originally Posted by scottn2retro

Hi All -

On our 135i race car, we're moving up in class, so I'm doing kind of 1M front conversion.
https://www.facebook.com/sctsracing/...type=3&theater

So far, I've only used the 1M front bumper, fenders and front fender liners, but we're a race car going to be in prepared class. For a nice street car, I can definitely see wanting to do the rocker panels and rear fender liners. You could easily fab a piece of plastic from the removed fender liners (and use the speed clips) to fill the 2 holes in between the front center undertray and the new 1M front fender liners

I'm having a hard time sorting through this. I need to rebuild the front end of my new 135i. Other than the bumper/fenders/liners did you need to change the bumper mounts/rad support or any other mount points.

[ilikebmxbikes]

Originally Posted by Ingeniator

I'm having a hard time sorting through this. I need to rebuild the front end of my new 135i. Other than the bumper/fenders/liners did you need to change the bumper mounts/rad support or any other mount points.

You need:

Front Bumper
Headlight brackets
Fender Liners ( 2 parts per side)
Underbody Shield
Front Fenders
Side Markers
Windshield Washer Fluid Reservoir
Front Bumper Ducting

Headlight Washers ( Cut to use 135i ones / Upgrade to 1M ones / Delete them)