BMW 1 Series Coupe Forum / 1 Series Convertible Forum (1M / tii / 135i / 128i / Coupe / Cabrio / Hatchback) (BMW E82 E88 128i 130i 135i)
 





 

Post Reply
 
Thread Tools Search this Thread
      04-20-2020, 12:46 PM   #1
fe1rx
Captain
1390
Rep
776
Posts

Drives: 135i, 328i, Cayman S
Join Date: Jan 2008
Location: Canada

iTrader: (3)

fe1rx adds full aero

My path down aero lane has taken a serious turn this winter with the addition of a full underbody treatment. In aero terms, I call this my V3 configuration, as it follows V1 and V2, which were variations on a wing and a splitter.

Name:  AERO GEOMETRY V1.jpg
Views: 3281
Size:  37.5 KB

V1.0 (October 2018) consisted of a Bimmerworld “V3 Carbon Race Wing Medium” and a custom 5” extension splitter. This wing installs high enough that rearward visibility is unimpeded.

Name:  W1 Wing.jpg
Views: 3258
Size:  78.2 KB

The Bimmerworld supplied hardware assumes through-bolting into the trunk lid, but as the fasteners install into closed cavities and would require internal trimming to get nut access, I installed mine with 10-32 rivnuts using the supplied rubber gasket

Name:  W2 Rivnuts.JPG
Views: 2732
Size:  166.0 KB

Name:  W3 Rubber Gasket.JPG
Views: 2680
Size:  188.9 KB

The upright is drilled for ¼” bolts, but I installed nylon washers to reduce the holes for 10-32 UNF structural stainless hardware.

Name:  W4 Trunk Lid Wing Fastener.jpg
Views: 2672
Size:  177.5 KB

The uprights required a slight bend adjustment to perfectly match the slope of the trunk lid.

Name:  W5 Wing Standoff.jpg
Views: 2895
Size:  235.7 KB

To prevent the wing from striking the rear glass when the trunk is opened, I installed limiting cables.

Name:  W6 Wing Safety Cables.jpg
Views: 2902
Size:  228.0 KB

Name:  W7 Wing to Glass Clearance.jpg
Views: 3061
Size:  216.7 KB

Adjustment of the wing uses an interesting slot geometry that keeps the wing trailing edge height constant as the angle is changed rather than using one fixed pivot point and one sliding. This may be beneficial when racing in classes with a maximum wing height.

Name:  W8 Wing Adjusting.jpg
Views: 2686
Size:  241.2 KB

If installing the wing is a 1 in degree of difficulty, fabricating a custom front splitter is about a 3.

The splitter was fabricated from 3/8” HDPE, solidly supported at the back by a bracket attached to the front subframe and at the front by means of fixed stays attached to the bumper impact beam by means of rivnuts and eyebolts. A quick and dirty air dam seal was created with duct tape to seal the gap between the splitter and the bumper cover.

Name:  S1.1 V1.0 Splitter.jpg
Views: 2706
Size:  86.9 KB

Name:  S1.2 Bumper Beam Rivnut.jpg
Views: 2778
Size:  253.1 KB

Sorting out the geometry was simplified by making a prototype out of clear lexan.

Name:  S1.3 Splitter Lexan Trial.jpg
Views: 2788
Size:  98.3 KB

The actual design was modeled in CAD and the finished splitter was cut on a CNC mill. Given that splitters are consumable, and I figured I would be going through a few different versions, having a quick way to make identical or adjusted replacements is useful.

Prior to driving the splitter, I asked a friend to give it the standard “stand on it” proof loading.

Name:  S1.4 Splitter V1 Proof Loading.jpg
Views: 2734
Size:  114.7 KB
Appreciate 11
Suprgnat2282.50
spidertri394.50
135113.00
asbrr540.50
519.E82243.00
bchalks31.50
houtan701.00
chris82827.00
Brian_9.00
      04-20-2020, 12:52 PM   #2
fe1rx
Captain
1390
Rep
776
Posts

Drives: 135i, 328i, Cayman S
Join Date: Jan 2008
Location: Canada

iTrader: (3)

V2

V2.0 (May 2019) lowered the splitter to 100 mm and added a HDPE air dam. The V2 splitter was installed with zero rake. The outer ends also incorporated air dams / vortex generators, and sacrificial Delrin wear pucks.

Name:  AERO GEOMETRY V2.jpg
Views: 2803
Size:  39.9 KB

Name:  S2.1 V2.0 At Mosport.jpg
Views: 2792
Size:  90.9 KB

Name:  S2.2 Splitter V2 Detail.jpg
Views: 2687
Size:  182.1 KB

V2.1 (July 2019) added hood vents and splitter diffusers and lowered the splitter to 84 mm. At this splitter height, the wear pucks see a bit of wear on track but the splitter itself shows only very light scraping, so this splitter height is close to minimum for my ride height and suspension stiffness.

Name:  S2.3 Splitter V2.1 Diffuser Detail.jpg
Views: 2718
Size:  168.0 KB

The splitter diffusers were fabricated from welded aluminum and have a rather modest ramp angle.

The stay rods, originally fixed length aluminum, were replaced with cables to permit the splitter to move upward if it contacted the ground.

Name:  S2.4 Splitter V2.1.jpg
Views: 2723
Size:  99.4 KB

The hood was modified for installation of Trackspec hood vents.

Name:  H1 V2.1 Trackspec Cutouts.jpg
Views: 2649
Size:  200.1 KB

Name:  H2V2.1 Trackspec Installed.jpg
Views: 2725
Size:  155.7 KB

Last edited by fe1rx; 04-20-2020 at 07:16 PM.. Reason: removing duplicate image
Appreciate 6
Suprgnat2282.50
spidertri394.50
135113.00
asbrr540.50
519.E82243.00
      04-20-2020, 01:02 PM   #3
fe1rx
Captain
1390
Rep
776
Posts

Drives: 135i, 328i, Cayman S
Join Date: Jan 2008
Location: Canada

iTrader: (3)

V3 - Preparation

V3.0 (currently in progress) lowered the splitter further and adds a full underbody treatment. If installing a custom splitter is a 3 effort, installing a custom underbody is an 11.

Name:  AERO GEOMETRY V3.jpg
Views: 2681
Size:  48.8 KB

I will describe each of the underbody sections in separate posts, as they progress, but first some preparatory actions were needed to free up the space required by the planned underbody treatment.

I am happy with my current suspension ride height, so to adjust the underbody ground clearance, it needs to be spaced down below the body. To function properly it needs to keep engine cooling air out from underneath itself. Therefore heat management (engine cooling air, and air to cool the exhaust, transmission and differential) needs to be addressed with appropriate sealing and cooling ducts. Also, appropriate structural attachments are required to mount the underbody.

To reduce the exhaust heat load, I replaced my N54 mid-pipe with an N55 mid-pipe, and wrapped the pipes with exhaust wrap. Eliminating the cats should remove some of the underbody heat also.

Name:  X1 Mid Pipe Comparo.jpg
Views: 2804
Size:  121.1 KB

To avoid conflict between my OE axle back and the planned diffuser, I built a new axle-back from 3” mandrel bent tube and a Vibrant muffler.

Name:  X2 Welded Assembly.jpg
Views: 3088
Size:  133.1 KB

The axle back uses the existing hanger locations.

Name:  X3 Fit around Diff.jpg
Views: 2836
Size:  247.8 KB

Name:  X4 Installed from Rear.jpg
Views: 2806
Size:  242.1 KB

Based on the heat colours revealed after a track outing, the axle-back tubing gets quite hot, so this too was wrapped with exhaust wrap.

Name:  X5 Heat Colours.JPG
Views: 2658
Size:  245.9 KB

Name:  X6 Axle Back Installed 2.JPG
Views: 2832
Size:  293.1 KB

Name:  X7 Axle Back Installed 4.JPG
Views: 2802
Size:  274.0 KB

My car is self-supporting and it tows a Leroy Engineering Paddock (2017) trailer to the track.

Name:  TH1 V2.0 DDT.jpg
Views: 2686
Size:  359.7 KB

The originally installed Curt hitch intruded into the planned diffuser space, so I built a custom trailer hitch to eliminate this conflict.

Name:  TH2 CURT vs ROXY.jpg
Views: 2711
Size:  211.4 KB

Conveniently, the hitch also serves as an attach point for the diffuser.

Name:  TH3 Tow Hitch Angle LH.jpg
Views: 3224
Size:  212.9 KB

Name:  TH4 Tow Hitch Angle RH.jpg
Views: 2851
Size:  206.8 KB

more to follow ...
Appreciate 10
Suprgnat2282.50
spidertri394.50
135113.00
asbrr540.50
1and11851.50
houtan701.00
BMWWorld234.50
      04-20-2020, 02:24 PM   #4
$iriu$black
Captain
241
Rep
616
Posts

Drives: 2012 BMW 128
Join Date: Dec 2014
Location: NE

iTrader: (5)

A proper track setup. Well done again, fe1rx. Do you run Time Trials?
Appreciate 1
fe1rx1390.00
      04-20-2020, 02:43 PM   #5
Suprgnat
Слава Украине!
Suprgnat's Avatar
Ukraine
2283
Rep
2,427
Posts

Drives: 2013 128i LMB 6MT ZMP Slicktop
Join Date: Jan 2013
Location: California

iTrader: (7)

Garage List
2013 128i  [9.58]
Always a pleasure, always educational, always an inspiration.
__________________
Inertia is the enemy!
My car's photo history: https://www.1addicts.com/forums/show....php?t=1570551
Appreciate 3
fe1rx1390.00
Rundskop145.00
AmuroRay2165.00
      04-20-2020, 07:24 PM   #6
fe1rx
Captain
1390
Rep
776
Posts

Drives: 135i, 328i, Cayman S
Join Date: Jan 2008
Location: Canada

iTrader: (3)

Quote:
Originally Posted by $iriu$black View Post
A proper track setup. Well done again, fe1rx. Do you run Time Trials?
I ran Time Trials regularly with my previous track car (an FC Turbo II RX-7). I have done a couple with this car but I am building it to be the car I want to drive at the track, rather than optimizing it within any particular rule set. I am building this car just for lapping days.
Appreciate 3
dtla1826.00
houtan701.00
Rundskop145.00
      04-20-2020, 07:49 PM   #7
$iriu$black
Captain
241
Rep
616
Posts

Drives: 2012 BMW 128
Join Date: Dec 2014
Location: NE

iTrader: (5)

Quote:
Originally Posted by fe1rx View Post
I ran Time Trials regularly with my previous track car (an FC Turbo II RX-7). I have done a couple with this car but I am building it to be the car I want to drive at the track, rather than optimizing it within any particular rule set. I am building this car just for lapping days.
Ah that’s what I figured. Just from the way you built the car, it would easily fit into TT4 or even higher (NASA) since yours is a 135i. Anyway, love the work and kind of reminds me of Jack Olsen’s 911 RSR. You drive it to the track, wring it out at the track, then drive home in it. Cheers from the Northeast!
Appreciate 1
fe1rx1390.00
      04-21-2020, 08:55 AM   #8
135
Captain
Australia
113
Rep
682
Posts

Drives: 135i
Join Date: Sep 2012
Location: Australia

iTrader: (4)

fe1rx Amazing work once again! I've been contemplating doing this exact same thing for some time now so I'll be following with keen interest.

Did you do any testing or use any data for high and low pressure zones and vent placement on the bonnet/hood?
There was someone on e90post or m3post that did some testing which would likely translate for our 1-series.
I ended up removing the under-bonnet cowl (cabin filter cover), even though it probably goes against what should be done in terms of pressure. I removed it for ease of access and to try and remove some hot air (also M3 strut brace fitted) - I never got around to doing the M3 cowl replacement - and I ended up using the BMS cowl filters.

I also wanted to get some inbound cold air (forward of where you have your side vents) to directly feed into my air filter (relocated to the hot side) but there wouldn't seem to be much room at all with your side vents' current placement.
Appreciate 1
fe1rx1390.00
      04-21-2020, 10:55 AM   #9
bbnks2
Colonel
1207
Rep
2,025
Posts

Drives: 135i N55
Join Date: Jan 2017
Location: NY

iTrader: (0)

Have you seen any of AJ Hartmans youtube videos? He shares quite a bit of his wind tunnel testing info. Asking because you are choosing to run a positive angle of attack on the front splitter which generally doesn't test well.

Before Typseed got his M2 in the hands of AJ the wind tunnel showed his Aero was creating front-end lift and had like 800lb of rear down-force. Crazy imbalanced. They had to make the front splitter angle more aggressive and basically take all of the angle of attack out of the rear wing. Then by adding canards they were able to bump the front downforce up a bit more for what ended up being a still rear-ward biased aero package but much more neutral than where the car started.
Appreciate 2
fe1rx1390.00
      04-21-2020, 01:10 PM   #10
fe1rx
Captain
1390
Rep
776
Posts

Drives: 135i, 328i, Cayman S
Join Date: Jan 2008
Location: Canada

iTrader: (3)

Quote:
Originally Posted by bbnks2 View Post
Have you seen any of AJ Hartmans youtube videos?
Thanks for that lead. Interesting, if somewhat tedious to wade through his videos. He does a lot of talking but it is hard to extract much data from what he says (at least in the videos I had a look at). I didn't find the one with different splitter angles. If you can provide a link to that, that would be great.

Splitter incidence is of course pretty easy to change. I suspect the effect of incidence may be different when the splitter is followed by a flat undertray. Anyway, you have to start somewhere and then test and modify from there. Getting the car in a wind tunnel would be great, but would logically require me to have multiple things to try out to see what works best. I need to finish 3.0 before I can start on 3.1, 3.2 3.3 ...
Appreciate 0
      04-21-2020, 06:12 PM   #11
Mark Aubele
Private
43
Rep
82
Posts

Drives: '12 135i
Join Date: Sep 2017
Location: Pittsburgh, Pa

iTrader: (0)

Quote:
Originally Posted by bbnks2 View Post
Have you seen any of AJ Hartmans youtube videos? He shares quite a bit of his wind tunnel testing info. Asking because you are choosing to run a positive angle of attack on the front splitter which generally doesn't test well.

Before Typseed got his M2 in the hands of AJ the wind tunnel showed his Aero was creating front-end lift and had like 800lb of rear down-force. Crazy imbalanced. They had to make the front splitter angle more aggressive and basically take all of the angle of attack out of the rear wing. Then by adding canards they were able to bump the front downforce up a bit more for what ended up being a still rear-ward biased aero package but much more neutral than where the car started.
Yeah, at least set the front splitter to 0 degrees. Preferably a degree down, with it pointed upwards you are likely creating front lift.
Appreciate 0
      04-22-2020, 03:10 AM   #12
Maverickmaxx
Registered
0
Rep
2
Posts

Drives: 2009 BMW 135i
Join Date: Sep 2017
Location: Queenstown, New Zealand

iTrader: (0)

Trackspec Hood Vents

The hood was modified for installation of Trackspec hood vents.



Looks really good, which vents did you go with?
Appreciate 0
      04-22-2020, 11:48 AM   #13
fe1rx
Captain
1390
Rep
776
Posts

Drives: 135i, 328i, Cayman S
Join Date: Jan 2008
Location: Canada

iTrader: (3)

Quote:
Originally Posted by 135 View Post
fe1rx Amazing work once again! I've been contemplating doing this exact same thing for some time now so I'll be following with keen interest.

Did you do any testing or use any data for high and low pressure zones and vent placement on the bonnet/hood?
There was someone on e90post or m3post that did some testing which would likely translate for our 1-series.
I ended up removing the under-bonnet cowl (cabin filter cover), even though it probably goes against what should be done in terms of pressure. I removed it for ease of access and to try and remove some hot air (also M3 strut brace fitted) - I never got around to doing the M3 cowl replacement - and I ended up using the BMS cowl filters.

I also wanted to get some inbound cold air (forward of where you have your side vents) to directly feed into my air filter (relocated to the hot side) but there wouldn't seem to be much room at all with your side vents' current placement.
Thanks. I had very little ability to move the vents forward or back. That area of the hood should be a low pressure area though. I did do some flow visualization with home-made flow viz, and the side vents are aligned with the local streamline direction on the hood.

Removing the cowl will likely not have your intended air flow intent as this is a high pressure area. Outside air is expected to flow in at that point, not out. Some wool tufts on the very back of your hood will reveal the flow direction very quickly.
Appreciate 1
135113.00
      04-22-2020, 11:51 AM   #14
fe1rx
Captain
1390
Rep
776
Posts

Drives: 135i, 328i, Cayman S
Join Date: Jan 2008
Location: Canada

iTrader: (3)

Quote:
Originally Posted by Maverickmaxx View Post
The hood was modified for installation of Trackspec hood vents.
Looks really good, which vents did you go with?
Thanks.

I went with the E90 E92 M3 Center Vent (E9092M3CL) plus two Large Rectangular Univeral Hood Louvers (U5512SHL).
Appreciate 0
      04-22-2020, 05:26 PM   #15
fe1rx
Captain
1390
Rep
776
Posts

Drives: 135i, 328i, Cayman S
Join Date: Jan 2008
Location: Canada

iTrader: (3)

Diffuser details

Other diffuser attach points were installed at the aft subframe bushing bolts,

Name:  AP1 RSFB Hard Point.jpg
Views: 2554
Size:  274.0 KB

Name:  AP2 RSFB Hard Point.jpg
Views: 2557
Size:  271.4 KB

at both ends of the rear bumper impact beam,

Name:  AP3 Bumper Support Strap.jpg
Views: 2583
Size:  210.9 KB

at the tension struts,

Name:  AP4 Tension Strut 3.JPG
Views: 2566
Size:  270.2 KB

and at the jack pad hard points with a cross bar, while incorporating low-profile lifting pads.

Name:  AP5 Tension Strut and Cross Bar.JPG
Views: 2584
Size:  238.6 KB

The chosen diffuser profile conflicts with the camber arms at full droop, but not under any normal driving conditions. To maintain a smooth aero surface, spring-loaded “landing gear doors” were installed. The hinges incorporate a pair of mouse trap springs to provide the door closing torque.

Name:  CD1 Door.jpg
Views: 2621
Size:  139.1 KB

Name:  CD2 Door.JPG
Views: 2532
Size:  204.2 KB

A removable access panel is provided to retain the ability to jack at the differential.

Name:  J1 JACK ACCESS.jpg
Views: 2548
Size:  238.9 KB

With a sealed underbody, the differential is now immersed in a hot air stream from both the engine compartment and due to the presence of the exhaust pipes. To provide a stream of cooling air to the differential, a NACA duct has been installed.

Name:  N1 NACA INLET.jpg
Views: 2575
Size:  198.2 KB

Because I couldn’t find anything I liked commercially, the NACA ducts were fabricated. The inlet incorporates a diffuser section and both this and the inlet were fabricated by hammer forming 3003 aluminum sheet over forming blocks and TIG welding. The diffuser section of the NACA duct decreases the velocity of the air in the duct, increasing its pressure. This ensures that air will not inadvertently flow out of the NACA inlet rather than in.

Name:  N2 NACA Inlet Welded Asssembly Outlet Side.jpg
Views: 2786
Size:  229.6 KB

The diffuser skin has been fabricated from 7075T6 0.063” aluminum sheet. This is a high strength alloy and is significantly tougher than 6061T6. Four strakes have been fitted in the forward part of the diffuser, and two more in the forward part. The strakes are made from 3/8” thick HDPE. These are potential wear items so are readily replaceable. The complete diffuser assembly including strakes weighs 33 lbs.

Bottom View:

Name:  D1 Diffuser Bottom View.jpg
Views: 2765
Size:  168.2 KB

Top View:

Name:  D2 Diffuser Top View.jpg
Views: 2779
Size:  168.5 KB

Some trimming of the battery box is required to accommodate the diffuser.

Name:  D3 Battery Box Mod.jpg
Views: 2541
Size:  266.2 KB

I have trimmed the original plastic “diffuser” trim to provide a somewhat finished appearance. The opening above the diffuser skin exits cooling air that has traveled above the underbody skin.

Name:  D4 Diffuser Trim LH.jpg
Views: 2494
Size:  211.9 KB

Name:  D5 Diffuser Trim RH.jpg
Views: 2603
Size:  203.3 KB

This completes the diffuser installation. Description of the middle and forward sections will follow …
Appreciate 5
asbrr540.50
spidertri394.50
135113.00
BMWWorld234.50
      04-23-2020, 07:59 AM   #16
asbrr
Major
Canada
541
Rep
1,233
Posts

Drives: 2014 335ix M-Sport
Join Date: May 2015
Location: Toronto

iTrader: (1)

Love all the little details like the access to jack points and the "landing gear door"! Fantastic work once again, looking forward to further info..
Appreciate 1
fe1rx1390.00
      04-28-2020, 10:48 AM   #17
amg6975
Captain
amg6975's Avatar
487
Rep
634
Posts

Drives: '12 M1.5, '05 ZHP, '98 M3/4/5
Join Date: May 2017
Location: Rochester NY

iTrader: (0)

Wow, incredible work, love the double diffuser to cool the differential.
Appreciate 1
fe1rx1390.00
      04-30-2020, 09:15 PM   #18
berns
Captain
1557
Rep
672
Posts

Drives: '07 E90 335i
Join Date: Feb 2013
Location: Los Angeles, CA

iTrader: (1)

This is awesome. Wish I had an ounce of your skill, patience and resources.
Send over the rear diffuser please!
Appreciate 1
fe1rx1390.00
      04-30-2020, 10:39 PM   #19
AndyW
Supreme Galactic Commander (one galaxy over...)
AndyW's Avatar
United_States
650
Rep
1,771
Posts

Drives: '08 E93, '12 E82, '13 E93 M3
Join Date: Feb 2012
Location: Washington, USA

iTrader: (5)

If you marketed that diffuser and underbody, I would buy one...
__________________
Best,
Andy

'12 E82-PS2,Stoptechs,Clubsports+M3 bits,Accusump,Wagner DP+EVO III FMIC,ERCP,BMS Intake,Mason Strut Bar,Wedge Tune
Appreciate 2
fe1rx1390.00
      05-01-2020, 08:59 AM   #20
SCato
Gamera Garage #Ron1n
United_States
14
Rep
24
Posts

Drives: 2009 135i
Join Date: Jun 2015
Location: Atlanta, Ga

iTrader: (0)

Quote:
Originally Posted by AndyW View Post
If you marketed that diffuser and underbody, I would buy one...
same here!
Appreciate 1
fe1rx1390.00
      05-04-2020, 04:01 PM   #21
fe1rx
Captain
1390
Rep
776
Posts

Drives: 135i, 328i, Cayman S
Join Date: Jan 2008
Location: Canada

iTrader: (3)

Inlet Air Sealing

In order to maximize cooling effectiveness, I am sealing up the inlet air leaks around the radiator and intercooler. The sides of the radiator are well sealed, but there is a significant gap at the top of the radiator that provides a leakage path of about 16 square inches (about 25” x 5/8”). In order to seal this, I have packed the gap with a seal fabricated from a piece of -12 firesleeve inserted into a piece of -22 firesleeve. This material consists of a silicone outer sealing layer and an inner fiberglass insulating layer.

Name:  1 Firesleeve Cross Section.JPG
Views: 2551
Size:  212.2 KB

The gap, and the seal are easily visible through the kidney grills.

Name:  2 Radiator Seal.JPG
Views: 2369
Size:  247.0 KB

Sealing the intercooler is much more involved, as there are numerous leakage paths, totaling about 90 square inches of area. High pressure air at the face of the intercooler can leak as follows:

- upward, between the bumper impact beam and the radiator support
- sideward around the radiator support
- sideward through the inlet lip profile
- under the intercooler

I addressed these leak paths with a fabricated sheet metal baffle assembly.

Name:  3 Intercooler Baffles.jpg
Views: 2189
Size:  245.8 KB

The top baffle follows the curved contour of the bumper support and is screwed to it.

Name:  4 Top Baffle.jpg .JPG
Views: 2183
Size:  265.4 KB

The bottom baffle is secured to the intercooler using gear clamp elements to the mounting bolts.

Name:  5 Bottom.jpg
Views: 2211
Size:  220.9 KB

The sides are riveted to the bottom baffle and screwed to the top baffle. The inlet lip seals also screw to the sides.

Name:  6 Intercooler Baffles 2.JPG
Views: 2297
Size:  261.1 KB

The inlet lip leak path may not be so apparent, but it is visible in the following image. Air can flow around the lip and then sideways out through this gap.

Name:  7 Lip Leak Path.JPG
Views: 2243
Size:  225.9 KB

The lip seals install last.

Name:  8 Lip Seal.JPG
Views: 2184
Size:  217.2 KB

The outside air temperature probe installs in a grommet in the top baffle.

Name:  9 OAT Probe.JPG
Views: 2226
Size:  285.7 KB

Not much to see from the outside, but these details should improve cooling efficiency significantly.

Name:  10 Outside View Edited.jpg
Views: 2354
Size:  98.2 KB
Appreciate 7
135113.00
AndyW650.00
asbrr540.50
berns1557.00
houtan701.00
      05-04-2020, 08:00 PM   #22
tracer bullet
Brigadier General
tracer bullet's Avatar
United_States
2296
Rep
3,464
Posts

Drives: '11 135i , '15 X3 35i
Join Date: May 2011
Location: Saint Paul, MN

iTrader: (1)

That's thorough! But you / we knew it would be.

Summit Racing sells similar fire sleeve material that is black. Just an FYI if you ever tire of the orange.

Or, if any wishes to duplicate. Perhaps me. Hmm. When you mention -12 and -22 sizes, is that a reference to AN tube sizes? If so, I didn't see a 22 option, only 20 and 24.
Appreciate 3
fe1rx1390.00
dtla1826.00
AndyW650.00
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 07:26 AM.




1addicts
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST