11-26-2018, 09:03 PM | #1 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
1M ViE Single Turbo Build
I've been collecting bits and parts then posting them on one thread but I thought I would start a new thread with all the ups and downs so far.
Over the last 72 hours we stuffed all of this into the M: - ViE 3884 GTW 67mm 1.0AR Hot Side + OCD T51r Mod - NPT 1/2 to 10AN Oil Drain to VTTO Oil Drain block adapter - PR Coil Packs - PSP 900 IC - All Lines AN SS Braided (Water/Oil Return/Vac) - A lot of misc maint stuff (Water pump, bolts, nuts etc...) The car came out amazing but there a small to moderate things that need to be sorted. I am not sure if I can say this is due to the ViE kit or the 1M, though the 1M shares the 135i front sub frame so I cant see that creating variance. Also its a ViE one off kit due to the 1.0AR hot side. Summary of fun challenges: - Turbo sits very close to tower, AKG mounts ordered - Front Screamer touches water elbow , Will need a little fabbing - AN fitting on block for the Oil Return wedges on Pump to Thermo elbow, open to suggestions here - Rear O2 placement is too tight for my taste, Will need to have the bung moved back - Turbo must be clocked at 30 degrees due to Oil Drain, 30 is the max from what I've read so worrisome Here are some fun pictures of the good and not so good! PSP 900 IC is a monster and it always hurts to cut that much plastic out of the front. We called this our window into M hell, not a lot of room to fit all that 4an vac line for twin scroll Was able to push the OEM IC shroud back into place to help divert the air where its needed Mostly together for first start up Buttoned up with M3 cowl and Catch Can connected. Engine cover will require a lot of trimming t51r Mod Noises :-) https://onedrive.live.com/embed?cid=...BALBrmobi5lVcs Challenge: Front screamer touching waterline Challenge: Oil Drain touching elbow Ill most some more pics up but she is running and super healthy, started up fine with zero errors or codes. Car is on spring pressure for some shake downs and is a beast above 4k RPMs!
__________________
2011 BMW VO 1M (Currently in pieces for New Build!)
==OLD SETUP== ViE 3884 | PR | JB4 | EOS Billet Fuel / Manifold | Seibon Hood | Spec Twin | 900IC | Slek Lip / Diffuser | EC7 Wheels | KW HAS | Maddad + GTHaus | P3 | ViE Can Last edited by Six Pot; 11-26-2018 at 10:14 PM.. |
11-27-2018, 09:33 AM | #4 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
No additional oil cooling yet, I have a plan for that. There is definitely a lot more on the car , I’ll post a full build sheet soon.
__________________
2011 BMW VO 1M (Currently in pieces for New Build!)
==OLD SETUP== ViE 3884 | PR | JB4 | EOS Billet Fuel / Manifold | Seibon Hood | Spec Twin | 900IC | Slek Lip / Diffuser | EC7 Wheels | KW HAS | Maddad + GTHaus | P3 | ViE Can |
Appreciate
0
|
11-27-2018, 09:51 AM | #5 |
Buck Sgt
144
Rep 355
Posts |
can't wait, an additional oil cooler is what I think the 1M needed, even in stock form, it runs slightly hot. I believe with cooler oil temp, will help with durability and wear n tear. I have been driving slightly hard with the GT3, and temp never gone over 220, mostly around 200, but the 1M, just cruising around town, it's over 240* maybe your single turbo built and mod might be diff.
|
Appreciate
0
|
11-28-2018, 10:14 AM | #7 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
Will be coming very soon, right now we are doing initial shake downs on WG pressure and addressing the potential failure points. Also the weather has not been playing well :-/
__________________
2011 BMW VO 1M (Currently in pieces for New Build!)
==OLD SETUP== ViE 3884 | PR | JB4 | EOS Billet Fuel / Manifold | Seibon Hood | Spec Twin | 900IC | Slek Lip / Diffuser | EC7 Wheels | KW HAS | Maddad + GTHaus | P3 | ViE Can |
Appreciate
1
Tornado1M1211.00 |
11-29-2018, 09:37 AM | #8 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
Another piece of the puzzle being installed tonight. From what I have read this can raise the engine up almost 1", should give good clearance
__________________
2011 BMW VO 1M (Currently in pieces for New Build!)
==OLD SETUP== ViE 3884 | PR | JB4 | EOS Billet Fuel / Manifold | Seibon Hood | Spec Twin | 900IC | Slek Lip / Diffuser | EC7 Wheels | KW HAS | Maddad + GTHaus | P3 | ViE Can |
Appreciate
1
Tornado1M1211.00 |
12-02-2018, 11:06 PM | #9 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
Shake down proved too much for the cooling system. Removing the radiator and deleting the junk second radiator to make room for more fun. We also decided to address the clocking of the turbo, my buddy helped me figure out how to get it to be more at the 12/6 orientation. We have almost every defect hammered out!
__________________
2011 BMW VO 1M (Currently in pieces for New Build!)
==OLD SETUP== ViE 3884 | PR | JB4 | EOS Billet Fuel / Manifold | Seibon Hood | Spec Twin | 900IC | Slek Lip / Diffuser | EC7 Wheels | KW HAS | Maddad + GTHaus | P3 | ViE Can |
Appreciate
0
|
12-02-2018, 11:17 PM | #10 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
Cover cut and new DP Scavenger added
__________________
2011 BMW VO 1M (Currently in pieces for New Build!)
==OLD SETUP== ViE 3884 | PR | JB4 | EOS Billet Fuel / Manifold | Seibon Hood | Spec Twin | 900IC | Slek Lip / Diffuser | EC7 Wheels | KW HAS | Maddad + GTHaus | P3 | ViE Can |
Appreciate
0
|
12-08-2018, 12:33 AM | #11 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
Almost there
__________________
2011 BMW VO 1M (Currently in pieces for New Build!)
==OLD SETUP== ViE 3884 | PR | JB4 | EOS Billet Fuel / Manifold | Seibon Hood | Spec Twin | 900IC | Slek Lip / Diffuser | EC7 Wheels | KW HAS | Maddad + GTHaus | P3 | ViE Can |
Appreciate
0
|
12-13-2018, 02:33 PM | #13 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
Another day another part :-)
__________________
2011 BMW VO 1M (Currently in pieces for New Build!)
==OLD SETUP== ViE 3884 | PR | JB4 | EOS Billet Fuel / Manifold | Seibon Hood | Spec Twin | 900IC | Slek Lip / Diffuser | EC7 Wheels | KW HAS | Maddad + GTHaus | P3 | ViE Can |
Appreciate
0
|
01-02-2019, 01:26 AM | #14 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
Didn't have time to take it to the shop before it went to the fabricator to make some tweaks, So we quickly threw on the GTHAUS and got it brief video
__________________
2011 BMW VO 1M (Currently in pieces for New Build!)
==OLD SETUP== ViE 3884 | PR | JB4 | EOS Billet Fuel / Manifold | Seibon Hood | Spec Twin | 900IC | Slek Lip / Diffuser | EC7 Wheels | KW HAS | Maddad + GTHaus | P3 | ViE Can |
01-28-2019, 03:18 PM | #15 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
Little update video after coming back from the fabrication shop. still tweaking but getting closer and closer
__________________
2011 BMW VO 1M (Currently in pieces for New Build!)
==OLD SETUP== ViE 3884 | PR | JB4 | EOS Billet Fuel / Manifold | Seibon Hood | Spec Twin | 900IC | Slek Lip / Diffuser | EC7 Wheels | KW HAS | Maddad + GTHaus | P3 | ViE Can |
Appreciate
0
|
02-01-2019, 02:56 PM | #17 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
|
Appreciate
0
|
03-19-2019, 10:14 AM | #19 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
Removed the secondary cooler when I went to CSF since it has plenty of cooling capacity. In the process of fitting dual oil coolers and take advantage of the additional space :-)
|
Appreciate
0
|
04-16-2019, 11:43 AM | #20 |
Lieutenant
416
Rep 441
Posts
Drives: 1M
Join Date: Jun 2010
Location: Cincinnati
|
New tires fitted, 615k+ with a 295/40/18 in the rear :-)
__________________
2011 BMW VO 1M (Currently in pieces for New Build!)
==OLD SETUP== ViE 3884 | PR | JB4 | EOS Billet Fuel / Manifold | Seibon Hood | Spec Twin | 900IC | Slek Lip / Diffuser | EC7 Wheels | KW HAS | Maddad + GTHaus | P3 | ViE Can |
Post Reply |
Bookmarks |
|
|