|
|
|
04-27-2024, 03:22 PM | #1 |
Lieutenant
336
Rep 536
Posts |
128i - harness above engine, plastic clip mounts
Somehow, the three mounts that hold the wiring harness (above the motor) in place have broken, see pictures. What do I need to do to fix this? Plastic gets brittle w heat
|
04-27-2024, 06:33 PM | #2 |
Second Lieutenant
443
Rep 290
Posts |
I don't know for sure without seeing it in person or looking at my car and I'm a bit too lazy to do that rn.
I think you either need 12527532268 or 12527534161. I could be wrong, double check realoem diagrams (i found these under Engine Electrical System).
__________________
2011 BMW 128i 6MT M Sport - Alpine White on Terracotta w/ Glacier-Silver trim - Koni Yellows w/ H&R Sport Springs, M3 Control Arms, Euro Intake, BMW Performance Exhaust, 3.73 Diff w/ RacingDiffs LSD Conversion, Black Line Taillights, M Performance Grilles, lots-o-maintenance
|
Appreciate
1
cerealwars78.00 |
04-28-2024, 01:28 AM | #3 |
Second Lieutenant
94
Rep 269
Posts |
I think this might be the lower part of the cabin microfilter compartment, part #2 on this page: https://www.realoem.com/bmw/enUS/sho...diagId=64_1428
I also have the driver's side tabs broken off, and the center is not held up very solidly, either. A fragile part that isn't inexpensive. Good luck.
__________________
E9x M3 front & rear suspension arms; BMW Performance brakes upgraded to drilled rotors in rear; BMW performance shifter; BMW Performance Exhaust; Wave Trac LSD with modified 'nannies'; BMW Euro Intake box; BMW Aluminum Strut Tower bar; ECS front and rear sway bars; 3 stage intake with BPC software; BMW style 78, 17 x 8" wheels with Bridgestone RE 980AS 225/45-17 tires; Koni Special Active struts/shocks, E9x M3 RTABs.
|
Appreciate
3
|
04-28-2024, 09:02 AM | #4 |
Lieutenant
336
Rep 536
Posts |
Thanks, I’ll do more research and report back
This could be a job for the all-powerful “zip tie” in matte black |
Appreciate
3
|
04-28-2024, 05:12 PM | #5 |
BMW Owner Since 1971
2263
Rep 1,410
Posts
Drives: 1964 700 Sport Cabriolet
Join Date: Apr 2014
Location: Central Virginia
|
I've been thinking maybe a drill and some push-pin rivets like the trunk linings use?
|
Appreciate
0
|
04-29-2024, 08:57 AM | #6 |
Major
788
Rep 1,004
Posts |
My cabin air filter cover tabs were very brittle and I snapped both front tabs off when I tightened them down one time. A replacement cover wasn't too expensive. As mkeiser said, you probably just need the perch which is only around $30. Considering you need to pull that harness almost any time you do something under the hood, I would fix it properly.
__________________
Official BMWP Whore - BMWP suspension kit w/ M3 arms, BMWP big brake kit, BMWP intake w/Mishimoto tube, BMWP exhaust, BMWP carbon strut brace, BMWP short shifter, and BMWP carbon spoiler. OZ Leggera HLT w/ 245 square setup.
|
Appreciate
1
jdt10768336.00 |
04-29-2024, 09:19 AM | #7 | |
Lieutenant
336
Rep 536
Posts |
Quote:
|
|
Appreciate
0
|
04-29-2024, 03:04 PM | #8 |
Private First Class
144
Rep 117
Posts |
Don't they slide in here?
|
Appreciate
0
|
04-29-2024, 03:38 PM | #9 |
Lieutenant
336
Rep 536
Posts |
No, it looks like they should - but look about 3/4" to the right of your arrows and you'll see where they are supposed to slide/clip in to the little box shaped pieces (the left hand box is broken / bottom broken off)
|
Appreciate
0
|
Today, 11:24 AM | #10 | |
Second Lieutenant
370
Rep 296
Posts
Drives: 2010 128i ZSP 6MT
Join Date: Jun 2007
Location: Puget Sound Region
|
Quote:
(I have the same problem and it is in my saved items on FCP Euro for sometime when I have something approximating disposable income)
__________________
2010 128i ZSP 6MT Coupe
Deep Sea Blue (Tiefseeblau) Metallic Style 264 Wheels Lemon Boston Sport Interior Last edited by Donkeyshins; Today at 11:29 AM.. |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|