Airbag fault code 9416

135mass · 05-25-2022, 08:41 PM

Hello I have a 2008 135i coupe. The airbag and seatbelt dash lights are lit. Using INPA the fault code is 9416. The fault code translator gives the following:

9416 ACSM/MRS: Seat occupancy, driver, incorrect: hardware does not support driver seat-occupancy detector acsm60 Crash safety module

9416 MRS: Retractor tensioner, left mrs5 Multiple restraint system

9416 SGM-SIM: Rollover bar, left: open circuit sgm_60_2 Safety and information module (SIM)

Has anyone seen this error code before? All searches on here seem to point to the passenger side occupancy sensor as being the problem, not the driver side. Also the occupancy sensor bypass solutions all seem to be for the passenger side. Am I missing something? Please let me know your collective thoughts. Thanks in advance for your help.

135mass · 08-25-2022, 09:40 PM

Bump

135mass · 01-30-2023, 09:07 PM

Update I replaced the driver seat seat belt latch and pretensioner unit. Presumably that would take care of the middle issue in the post above. Still have the same 9416 error code.

One item of note the replacement pretensioner unit
Bmw part number 72-11-7-213-563 D routes thru the yellow connector under the seat. The new part had a slightly different pin setup than the one I took out. The parts diagram had two different pretensioners. One for 4/08 production and later and one for earlier production dates. My 135 has a 4/08 production date so I used that part number above. Since my production date is right at the change date I am wondering if maybe mine used the prior part. Please chime in with any thoughts. Thx.

05-25-2022, 08:41 PM	#1
135mass New Member 10 Rep 20 Posts Drives: 2008 135i Join Date: Jun 2015 Location: New England iTrader: (0)	Airbag fault code 9416 - drivers side? Hello I have a 2008 135i coupe. The airbag and seatbelt dash lights are lit. Using INPA the fault code is 9416. The fault code translator gives the following: 9416 ACSM/MRS: Seat occupancy, driver, incorrect: hardware does not support driver seat-occupancy detector acsm60 Crash safety module 9416 MRS: Retractor tensioner, left mrs5 Multiple restraint system 9416 SGM-SIM: Rollover bar, left: open circuit sgm_60_2 Safety and information module (SIM) Has anyone seen this error code before? All searches on here seem to point to the passenger side occupancy sensor as being the problem, not the driver side. Also the occupancy sensor bypass solutions all seem to be for the passenger side. Am I missing something? Please let me know your collective thoughts. Thanks in advance for your help.
	Appreciate 0 Tweet Quote

08-25-2022, 09:40 PM	#2
135mass New Member 10 Rep 20 Posts Drives: 2008 135i Join Date: Jun 2015 Location: New England iTrader: (0)	Bump
	Appreciate 0 Quote

01-30-2023, 09:07 PM	#3
135mass New Member 10 Rep 20 Posts Drives: 2008 135i Join Date: Jun 2015 Location: New England iTrader: (0)	Update I replaced the driver seat seat belt latch and pretensioner unit. Presumably that would take care of the middle issue in the post above. Still have the same 9416 error code. One item of note the replacement pretensioner unit Bmw part number 72-11-7-213-563 D routes thru the yellow connector under the seat. The new part had a slightly different pin setup than the one I took out. The parts diagram had two different pretensioners. One for 4/08 production and later and one for earlier production dates. My 135 has a 4/08 production date so I used that part number above. Since my production date is right at the change date I am wondering if maybe mine used the prior part. Please chime in with any thoughts. Thx.
	Appreciate 0 Quote