BMW 1 Series Coupe Forum / 1 Series Convertible Forum (1M / tii / 135i / 128i / Coupe / Cabrio / Hatchback) (BMW E82 E88 128i 130i 135i)
 





 

Post Reply
 
Thread Tools Search this Thread
      10-28-2018, 06:03 AM   #45
hydra
Flaccid Member
hydra's Avatar
65
Rep
76
Posts

Drives: E82 135i 6MT F22 228i 6MT
Join Date: Feb 2016
Location: +961

iTrader: (0)

3" Inlets + custom airbox

It goes without saying that all the fancy turbo hardware in the world isn't going to amount to much if you can't feed your compressor with the densest air possible. I literally spent months attempting an Alpina B3S-style setup before abandoning it for a much simpler solution you will see in the pics below, which keeps the water-tank in its stock location, while providing a full 3" of flow, enough for 350-400bhp per turbo with minimal pressure drop, along with an enclosed airbox feeding the R turbo with provisions for the stock breather and heater built-in , no messy VTA setup here!
Attached Images
   
__________________
BSM 2010MY Euro 135i 6MT with many mods... Build thread below

http://www.1addicts.com/forums/showthread.php?t=1264997
Appreciate 1
Matticus913469.50
      10-28-2018, 06:07 AM   #46
hydra
Flaccid Member
hydra's Avatar
65
Rep
76
Posts

Drives: E82 135i 6MT F22 228i 6MT
Join Date: Feb 2016
Location: +961

iTrader: (0)

Cooling setup

And now, to turn our attention to the cooling system.. Since I wiped out a bearing and had to replace my stock oil cooler anyway, I ended up going with an OEM N55 water to oil cooler for faster warmup and less pressure drop. Of course this adds heat rejection into the coolant circuit, so I figured I would offset this somewhat with a CSF radiator and call it a day. But after studying the 1M/335is/PPK aux rad setup closely I came to the realization that the aux cooler uses EXACTLY the same heat exchanger as our stock oil cooler! Did a bit of thinking and decided it would be both easiest and best to run this in series with the N55 oil cooler, so that the coolant going into the oil cooler is a little bit cooler than that of the engine, basically trading off a bit of coolant-side effectiveness for oil-side capacity. I can always have a custom, higher-capacity heat exchanger made in the future, but preliminary testing has shown that oil temps are noticeably cooler with this setup already...
Attached Images
  
__________________
BSM 2010MY Euro 135i 6MT with many mods... Build thread below

http://www.1addicts.com/forums/showthread.php?t=1264997
Appreciate 1
Matticus913469.50
      10-28-2018, 06:17 AM   #47
hydra
Flaccid Member
hydra's Avatar
65
Rep
76
Posts

Drives: E82 135i 6MT F22 228i 6MT
Join Date: Feb 2016
Location: +961

iTrader: (0)

Twin plate OEM-style clutch

Reserved
__________________
BSM 2010MY Euro 135i 6MT with many mods... Build thread below

http://www.1addicts.com/forums/showthread.php?t=1264997
Appreciate 1
Matticus913469.50
      10-28-2018, 06:22 AM   #48
hydra
Flaccid Member
hydra's Avatar
65
Rep
76
Posts

Drives: E82 135i 6MT F22 228i 6MT
Join Date: Feb 2016
Location: +961

iTrader: (0)

Misc Odds & Ends

Reserved
__________________
BSM 2010MY Euro 135i 6MT with many mods... Build thread below

http://www.1addicts.com/forums/showthread.php?t=1264997
Appreciate 1
Matticus913469.50
      10-30-2018, 11:04 AM   #49
Matticus91
Brigadier General
Matticus91's Avatar
United_States
3470
Rep
3,722
Posts

Drives: 2013 135i
Join Date: Aug 2015
Location: Washington DC

iTrader: (6)

Wow this has gotten really interesting, can you convert those dyno numbers to HP/TQ for us? I wasn't sure if the nm ratings were a direct conversion in this case
__________________
"Tobias" 2013 135i ///M-Sport 6MT • Pure Stage 1 • XDI 35 HPFP • 404whp/440wtq
Appreciate 0
      10-31-2018, 03:51 AM   #50
hydra
Flaccid Member
hydra's Avatar
65
Rep
76
Posts

Drives: E82 135i 6MT F22 228i 6MT
Join Date: Feb 2016
Location: +961

iTrader: (0)

Quote:
Originally Posted by Matticus91 View Post
Wow this has gotten really interesting, can you convert those dyno numbers to HP/TQ for us? I wasn't sure if the nm ratings were a direct conversion in this case

Dyno numbers are from 2016 with an entirely different setup. Here is what I am expecting with my current combo:

~580whp SAE @ 17.4psi on 93oct pump gas no meth, ~500lb-ft of torque
~635whp SAE @ 21.4psi on 93oct pump gas no meth, ~550lb-ft of torque
~750whp SAE @ 26.1psi on race gas, ~700lb-ft of torque
__________________
BSM 2010MY Euro 135i 6MT with many mods... Build thread below

http://www.1addicts.com/forums/showthread.php?t=1264997
Appreciate 0
      10-31-2018, 08:33 AM   #51
Matticus91
Brigadier General
Matticus91's Avatar
United_States
3470
Rep
3,722
Posts

Drives: 2013 135i
Join Date: Aug 2015
Location: Washington DC

iTrader: (6)

That's going to be a beast!
__________________
"Tobias" 2013 135i ///M-Sport 6MT • Pure Stage 1 • XDI 35 HPFP • 404whp/440wtq
Appreciate 1
hydra64.50
      02-10-2019, 04:54 PM   #52
hydra
Flaccid Member
hydra's Avatar
65
Rep
76
Posts

Drives: E82 135i 6MT F22 228i 6MT
Join Date: Feb 2016
Location: +961

iTrader: (0)

All done finally!
And now to actually drive this thing!
Attached Images
     
__________________
BSM 2010MY Euro 135i 6MT with many mods... Build thread below

http://www.1addicts.com/forums/showthread.php?t=1264997
Appreciate 3
Matticus913469.50
atch41719.50
b3turbo1273.50
      02-11-2019, 03:25 PM   #53
Matticus91
Brigadier General
Matticus91's Avatar
United_States
3470
Rep
3,722
Posts

Drives: 2013 135i
Join Date: Aug 2015
Location: Washington DC

iTrader: (6)

Looks great!
__________________
"Tobias" 2013 135i ///M-Sport 6MT • Pure Stage 1 • XDI 35 HPFP • 404whp/440wtq
Appreciate 1
hydra64.50
      06-16-2020, 07:36 PM   #54
b3turbo
Private First Class
b3turbo's Avatar
United_States
1274
Rep
173
Posts

Drives: 2010 FBO 135i
Join Date: Jun 2015
Location: Ukraine

iTrader: (0)

Any updates on your build ? did you dyno your new setup ?
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 12:28 PM.




1addicts
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST