|
|
|
07-01-2017, 11:43 PM | #331 |
!
693
Rep 3,266
Posts
Drives: 2010 128i
Join Date: Feb 2010
Location: Anacortes, WA
|
Nothing too exciting lately - just catching up on routine maintenance. I'm a little overdue for a rear diff fluid change, about 4-5 months late, to be exact. Although, I've on,y put about 1,000 miles on the car in that time, so I'm not to worried about it.
I'v actually had all the parts needed for quite a while: a fluid extractor, a couple of quarts of Red Line 80W-140 GL-5 gear oil, and an OE replacement fill plug. The thing that was holding me back was a need to be able to get the car high enough in the air to work underneath, while also keeping the car level (so as not to over- or underfill the differential). And then I also had to move rather suddenly, and we decided to buy a house, so it's been super busy. I finally got the garage unpacked and organized, and as much as I wish I could've installed a lift, I decided to go a different direction. I picked up a set of four JackPoints jack stands. These are pretty popular in the P-car community - they allow you to jack up your car by the factory jack point, and then place a jack stand underneath the same jack point. Probably the easiest way to get a car onto four stands, especially a lowered car. My car is quite low, and the short wheelbase of the 1er makes jacking a little more difficult as well, so it still took working with a combination of ramps and two jacks to get the car up on all four corners, but I did it: The nice thing is these stands are super stout and wide-based, and include appropriate jack-pad adapters - so the entire arrangement is quite sturdy. For good measure, I also placed blocks underneath the rear tires before I went underneath (you can see them in the next pic). Not much to say about the fluid transfer, other than I really wish we had proper drain plugs. A fluid extractor works well enough, but I'd really prefer being able to completely drain the rear diff and flush it out with clean fluid before filling. On a side note, I finally got to experience the very distinctive smell of used diff fluid - smells sort of like a cross between fuel and BO. Very weird! I used a generic fluid pump to refill the diff. Unfortunately, the Red Line bottles are a unique shape and there is no pump on the market that threads onto them, so it's a bit awkward to kind of hold the pump onto the bottle while simultaneously working the pump, but it works. I don't get why a company like Red Line would sell their products in non-standard sized bottles, and not even sell a proprietary pump, but oh well.
__________________
____________________________ |
Appreciate
2
bmw1racer998.00 andrey_gta298.00 |
07-05-2017, 03:53 PM | #332 |
House Stark
107
Rep 159
Posts |
LOVE the color of those wheels.
__________________
Kturbos
- E82 128i - E36 M3 - F82 M4 - Dodge Ram Rebel - "Everyone happens to know a few things, and one of the things we knows is, it’s not how you stand by your car, it’s how you race your car. You better learn that." |
Appreciate
0
|
07-05-2017, 04:19 PM | #333 |
!
693
Rep 3,266
Posts
Drives: 2010 128i
Join Date: Feb 2010
Location: Anacortes, WA
|
Thanks, me too! It's Triple Bronze by Prismatic Powders.
__________________
____________________________ |
Appreciate
0
|
07-06-2017, 07:35 AM | #334 |
House Stark
107
Rep 159
Posts |
Yeah I am a huge fan of any of the bronze variations. The bronze contrasts so well with the red body.
__________________
Kturbos
- E82 128i - E36 M3 - F82 M4 - Dodge Ram Rebel - "Everyone happens to know a few things, and one of the things we knows is, it’s not how you stand by your car, it’s how you race your car. You better learn that." |
Appreciate
0
|
07-10-2017, 10:59 PM | #335 |
!
693
Rep 3,266
Posts
Drives: 2010 128i
Join Date: Feb 2010
Location: Anacortes, WA
|
If you frequent the 128i section of this forum, you may have noticed another thread where I was talking about my problems with an uneven idle, some power loss at WOT, and persistent codes related to the eccentric shaft sensor. This is a fairly common issue with these engines, so it wasn't too surprising that I was facing it almost 7 1/2 years after my car's build date.
I ordered the parts a few weeks ago: a Genuine OE valve cover gasket set, Valvetronic motor gasket, and eccentric shaft sensor gasket (later I also ordered an oil filler cap gasket, based on the appearance of the original). For the eccentric shaft sensor itself, I decided to save a few bucks and go OEM and picked up a VDO unit. I'm nearly certain this is the same part as from the factory anyway. As long as I was going through all this trouble, I figured I'd do the spark plugs and coils, again going with OEM: Bosch for the coils and NGK for the plugs (literally the exact same part number on these). There are a bunch of posts on various BMW forums about this job, so I won't go into too much detail, except to say wow, what a pain in the ass. It's not technically difficult, but
Finally, if you recognize this: then you know the massive ordeal that is valve cover removal on these cars. You will swear, cry, and moan before you get to the picture above. A few more tips:
Anyway, that's all I can think of off the top of my head at the moment. I still have some ways to go before finishing - after snapping the pic above, I R&Red the faulty eccentric shaft sensor, as well as swapped out the spark plugs. You might notice in the lower right a new sport air filter - the original was installed almost 36,000 miles ago, and I'd rather just replace it than clean it. Not pictured is the valve cover, which was hosed down and allowed to dry overnight, before I pressed in the new gaskets. I didn't get a chance to refit the valve cover today, but hopefully tomorrow, and my inch-lb torque wrench should be here the following day - right now the plan is to have everything buttoned up and back together before the end of the week.
__________________
____________________________ Last edited by Bimmer-Bob; 07-12-2017 at 11:51 PM.. |
Appreciate
2
desertman1232213.50 andrey_gta298.00 |
07-11-2017, 09:59 AM | #336 |
Enlisted Member
21
Rep 30
Posts |
I did this same maintenance a few years ago at 45k on my 08 minus the coils. The vcg was the root of the repair but I did the ess so I wouldn't have to open it up again anytime soon. Make sure you get that back breather tube on correctly or you'll get a check engine light.
The car felt so good after this maintenance. Revs seemed to not drop as fast and better throttle response. At 86k now and have plugs and coils on the way. |
Appreciate
0
|
07-11-2017, 11:35 PM | #337 |
!
693
Rep 3,266
Posts
Drives: 2010 128i
Join Date: Feb 2010
Location: Anacortes, WA
|
Well, the good news is the valve cover goes on way easier than it comes off. Part of it is that I sort of knew the angle and rotation that was required (just did the reverse of removal), and I bought myself a little more clearance by removing the ignition coil insulators and peeling back the weather stripping from the firewall (both of which I recommend, if you were to remove the valve cover).
It's funny - I feel like if I could go back and do this job over again, it would be much smoother, but I guess that's the benefit of experience, and true of most situations. The weakness of the hobbyist mechanic is that for so many jobs that you do, it's your first (and often your last!) time doing it, unlike the dealer techs, who have R&Red countless N52 valve covers (not to mention the education and training they received, of course). But still, I guess there are lots of little lessons learned along the way that will apply at least somewhat to other projects, even if they're on different parts of the car, or different cars altogether. And besides - it's fun, sort of - isn't that why we do it in the first place?
__________________
____________________________ Last edited by Bimmer-Bob; 07-12-2017 at 11:48 PM.. |
Appreciate
2
desertman1232213.50 cerealwars78.00 |
07-12-2017, 02:30 PM | #338 |
E82 Mudflap Ambassador
2214
Rep 2,219
Posts
Drives: '08 128i
Join Date: May 2016
Location: Orlando, FL
|
Did you completely obliterate the spark plug tubes getting them out like I did? or were you smart about it and got them out unscathed?
__________________
My 2008 128i - Sparkling Graphite/Beige - Sport pkg - 6MT - Click me!
Parents' 2014 528i - Mineral White/Ivory White - fully loaded Instagram @Andreys_128i and @Honda.Bito |
Appreciate
0
|
07-12-2017, 09:14 PM | #339 |
!
693
Rep 3,266
Posts
Drives: 2010 128i
Join Date: Feb 2010
Location: Anacortes, WA
|
You know, I meant to pull them out before trying to get the valve cover off, but I forgot. I ended up not damaging them, but I took them off afterward, and I think that was one of the reason the valve cover went back on so much more easily.
__________________
____________________________ |
Appreciate
0
|
07-17-2017, 11:59 AM | #340 | |
New Member
11
Rep 22
Posts |
Nice car. Going back over your thread I noticed the Performance Brake Kit. Do you know if that was available from the factory as an order-able option on any year 128?
Quote:
|
|
Appreciate
0
|
07-18-2017, 01:12 AM | #341 |
!
693
Rep 3,266
Posts
Drives: 2010 128i
Join Date: Feb 2010
Location: Anacortes, WA
|
The Performance parts were available as port-installed accessories. So while not technically "factory" options, they could be specified on the build sheet and their cost amortized into the loan.
|
Appreciate
0
|
07-21-2017, 11:31 PM | #342 |
!
693
Rep 3,266
Posts
Drives: 2010 128i
Join Date: Feb 2010
Location: Anacortes, WA
|
I posted an update in the thread I had started about my trouble codes, but for the sake of completeness I wanted to mention it in my build thread. Got the car back together and it runs great - the idle is smoothing out, and the new air filter, plugs, and coils make the engine feel that much fresher. Whenever I drive this car after an extended break I'm always amazed at how great it feels.
After a couple of days, still no new codes thrown, and no leaks from the valve cover. For anyone thinking about tackling this on their own, know that it's a totally doable DIY. You need a little bit of experience, and certainly some patience your first go around. But I can't stress enough the need to have a good set of tools. This is what I came up with to get to one of the valve cover bolts tucked back under the passenger side of the firewall: That's almost every extension, adapter, and u-joint I have! And it was still a PITA (what are factory-trained techs even using to get at some of these fasteners?). The pictured inch-pound torque wrench was invaluable, and a new purchase for this job. I already had a couple of foot-pound wrenches, but nothing for fine work like the valve cover bolts, which you really don't want to screw up. One thing I hadn't heard mentioned is that all but two of the valve cover bolts seem to be captive in the cover - so don't be surprised when they don't come all the way out. On another, sillier note, I also finally took care of something that has been irking me for a while. I had the Performance brake kit fitted almost 3 years ago, and I remember sometime afterward looking at the instructions and seeing this section: Anyway, I realized that the dealer techs didn't put that label, whatever it was, on my car. I guess they just threw it away. Obviously it's completely immaterial and pointless, but it just kind of bugged me anyways. Well, a little while back I was messaging with forum member crowtrobot , who was installing the brake kit on his own 1er, and he went ahead and sent me an extra sticker he had. As it happens, there is no space on the driver's side B-pillar under the door lock, because of various other stickers that came from the factory, but there was space above the lock, so that's where it went: Kind of a stupid thing, I know, but I'm a completist, so it feels good to have the brake job finally "finished" (and period correct!). I kind of like any reference to the BMW Performance brand (like my limited edition carbon fiber license plate frame, and the brake calipers, both rocking the Performance Yellow), especially since BMW essentially killed the line when they rebranded it as ///M Performance - just kind of makes the old bits an odd little detour in BMW's history. Anyway, you can probably tell I spend way too much time thinking about stuff like this...
__________________
____________________________ |
Appreciate
0
|
07-27-2017, 07:34 PM | #343 |
Private
31
Rep 81
Posts |
Just finished reading through this thread, have to say I absolutely love your car. Very modest, but thought out mods.
On another note, my car's also crimson red, and I live in Bellingham, it'd be great to meet and compare cars at some point. Always wanted to see what a 128 is like, and if you'd be interested I do some phtogoraphy and would love to shoot your car. |
Appreciate
0
|
07-27-2017, 08:46 PM | #344 | |
Слава Украине!
2317
Rep 2,440
Posts |
Quote:
__________________
|
|
Appreciate
1
Bimmer-Bob692.50 |
07-29-2017, 12:00 PM | #345 | |
E82 Mudflap Ambassador
2214
Rep 2,219
Posts
Drives: '08 128i
Join Date: May 2016
Location: Orlando, FL
|
Quote:
I like this forum because we can be as anal as humanly possible and no one bats an eye. Personally, I wouldn't care that much about the sticker, but I do kinda like the "100%" aspect about it.
__________________
My 2008 128i - Sparkling Graphite/Beige - Sport pkg - 6MT - Click me!
Parents' 2014 528i - Mineral White/Ivory White - fully loaded Instagram @Andreys_128i and @Honda.Bito |
|
Appreciate
2
Bimmer-Bob692.50 cerealwars78.00 |
07-30-2017, 07:57 AM | #346 | |
!
693
Rep 3,266
Posts
Drives: 2010 128i
Join Date: Feb 2010
Location: Anacortes, WA
|
Quote:
__________________
____________________________ |
|
Appreciate
0
|
12-30-2017, 09:59 AM | #347 |
King of Goodness
152
Rep 185
Posts
Drives: 2012 128i Coupe
Join Date: May 2017
Location: Dixie
|
Nice car...nice read...
|
Appreciate
1
Bimmer-Bob692.50 |
01-06-2018, 06:43 PM | #348 |
Major
619
Rep 1,402
Posts |
When you are ready for more power and to do the 3 stage IM and BPC tune to make it work, and now that you are an expert at valve cover removal, you can add some more power with a set of MILVs which will add just over 1mm additional lift to your intake valves.
BPC has the tune for this. You can get their tune with 3IM and MILVs. They add 10-12rwhp across the whole rpm range. Do it all at once. Let me know when the time and 'power itch' comes. |
Appreciate
1
Bimmer-Bob692.50 |
01-20-2018, 07:56 AM | #349 |
Captain
594
Rep 704
Posts |
Nice build you got going, but i have two questions if you do not mind.
First how do you keep your eye on the oil temperature when you are tracking (or in general)? We do not get the 128i in Germany, we get a detuned version 125i, and it lacks any sort of temperature gauges, do you think it is possible to drop in gauges from the 130i/135i to display the oil temp? Secondly i noticed you tuned the car and getting around 220-230 at the wheels, how is the engine on track? nice and rev happy? i know it is not to be compared with a stock or modified 135i, but being normally aspirated makes it very attractive for me, but when i think of it, it is basically a RWD golf GTI (more or less). Thank you and keep up the good work. |
Appreciate
0
|
01-20-2018, 04:07 PM | #350 | |||
!
693
Rep 3,266
Posts
Drives: 2010 128i
Join Date: Feb 2010
Location: Anacortes, WA
|
Quote:
Quote:
Personally, I find either of these solutions to be somewhat cumbersome and inelegant, and would LOVE to have a real oil temp gauge in the cluster. For one thing, I just don't understand how it was left off of a coupe sold by an enthusiast marque like BMW. I mean, it seems like even econoboxes give you a temp gauge. Secondly, there's a huge empty spot on the cluster where it is supposed to go - it just seems like such a blatant cost-cut. I've thought about a cluster swap before, and even looked into it a little, but my attention has always been on other things. If anyone has any definitive knowledge on cluster swaps on theses cars, I'm all ears. I don't know if anyone has ever confirmed that the gauge would even work in our cars. Quote:
It's funny you mention the VW. I'd say that's kind of an apt comparison, hypothetically. Size, power levels, and target demographics are not that far off, but of course the drivetrain layouts are completely opposite. I've always thought that if VW ever cared enough to develop a RWD chassis, they could develop a downmarket sport sedan and make the GLI into a baby M3. Of course it wouldn't be as good, but it would cost half as much and younger folks would eat it up. Lots of people would love a RWD Euro sports sedan, far fewer can actually afford one.
__________________
____________________________ |
|||
Appreciate
0
|
01-20-2018, 04:50 PM | #351 | |
Captain
594
Rep 704
Posts |
Quote:
I found some discussions on the German 1er forums about this, some day it is a direct plug and play from the 135i some say coding is required, still investigating this. |
|
Appreciate
0
|
01-22-2018, 06:19 AM | #352 |
Captain
594
Rep 704
Posts |
Just an update regarding the gauges. I spoke with a shop that specializes in modifying gauges for BMWs, and i explained to them the lack of having an oil temperature gauge in the 125i.
They informed me that the 130i and 135i gauges (the ones with an oil temperature gauge) are a direct replacement, however the cluster needs to be coded. They offered me a €80 coding charge to have this done, used gauges work as well (does not have to be brand new). |
Appreciate
1
asbrr543.00 |
Post Reply |
Bookmarks |
|
|