► APEX | SM-10 Lightweight Track Wheels

[Expert@ApexWheels]

Thanks for your interest in our SM-10 wheels! This thread has been will no longer be updated, but the discussion continues on our combine Flow Formed wheel thread at: https://www.1addicts.com/forums/show...3#post25582133

We hope to see you there!

[HyeWarrior]

Oh damn.... I absolutely love these!

[ApexWheels]

Originally Posted by HyeWarrior

Oh damn.... I absolutely love these!

We agree! Can't wait to see these on many customer cars in the near future

-Matt

[ApexWheels]

Our new SM-10 wheels are available for pre-order and we are offering enthusiasts Free Shipping on a set of wheels for the rest of May. Check them out on our website here!

[ApexWheels]

We love the 10-spoke design featured on our new SM-10 wheels! Pre-Order today and be one of the first to run these wheels on your car

[Expert@ApexWheels]

What do you think about the new side-milled spokes on our SM-10 wheels? We sure do love them

[Expert@ApexWheels]

The new SM-10 wheels are scheduled for a June 2017 delivery! Pre-order today and be first to get your hands on a set of our new wheels!

[Expert@ApexWheels]

Most of our SM-10 wheels will be in stock this week, with remaining fitments arriving next week! We can't wait to see these wheels on your car!

[Dthltm]

Will you be making these in some 135i friendly offsets?

[Expert@ApexWheels]

Originally Posted by Dthltm

Will you be making these in some 135i friendly offsets?

Thank you for the comment! No plans for 1 series fitment just yet, but it may be something we consider in the future based on demand

-Matt

[Expert@ApexWheels]

A good portion of our new wheels have arrived today! Orders will begin shipping out this week, with the remaining wheels arriving next week

[Dthltm]

Originally Posted by Expert@ApexRaceParts

Thank you for the comment! No plans for 1 series fitment just yet, but it may be something we consider in the future based on demand

-Matt

[Expert@ApexWheels]

Check out our SM-10 wheels in the Satin Black finish! We have many sizes in stock and ready to ship. Remaining sizes will be in stock next week

[Expert@ApexWheels]

Here are some on-car pictures of the SM-10 wheels on a F80 M3! Wheels are in stock and ready to ship out! Place your order today

[ayao]

Like this design a lot!

[Newguy123]

So you post this on a 1 series forum with no 1 series fitment!?

Question do you guys have the arc8 in 17x9.5" size for track guys in 1 series offset?

[Expert@ApexWheels]

Originally Posted by ayao

Like this design a lot!

We appreciate the feedback

Originally Posted by Newguy123

So you post this on a 1 series forum with no 1 series fitment!?

Question do you guys have the arc8 in 17x9.5" size for track guys in 1 series offset?

Thank you for the response! Though we do not have any 1 series wheels in the SM-10 design just yet, we do have fitments available for the 1M. With that said, we may produce 1 series fitments in the future dependent on demand.

Our current 17x9.5" ET35 wheels are a bit too aggressive for the 1 series chassis. We do have our 17x8.5" ET40 wheels that would work well as a square setup, but require negative camber up front. Feel free to PM us if you have more questions regarding fitment!

-Matt

[lowside67]

Could you post a photo of the 18x8.5 +35 SM10 that shows the face profile/concavity? Will it take a stock BMW center cap?

Thank you,
Mark

[Expert@ApexWheels]

Originally Posted by lowside67

Could you post a photo of the 18x8.5 +35 SM10 that shows the face profile/concavity?  Will it take a stock BMW center cap?

Thank you,
Mark

Thanks for the post! Here's a photo showing the concavity of that wheel. This is an 18x9" ET30, but the face concavity profile is identical to the Profile 2 of the 18x8.5" ET35.



With that said, the 18x8.5" ET35 is quite aggressive for the 1 series chassis. For a direct fit, we recommend the 18x8.5 ET45 up front and 18x9.5 ET58 in the rear which is only available in our ARC-8 and EC-7 designs at this time. If you want to run the 18x8.5" ET35 as a square fitment on your 1 series, the wheel will extend out an additional 10mm front and rear compared to our recommended setup. Therefore, you will need to run negative camber up front and rear. In addition, a fender roll may also be needed in the rear to clear the fender. We recommend pairing that with a 245/35-18 tire. Feel free to give us a call if you want to go into more details regarding this fitment

-Dylan

[Expert@ApexWheels]

Our I-Beam spokes are beautifully functional.

[Expert@ApexWheels]

TIRES NOW AVAILABLE

[ShocknAwe]

Would love to see a rear non-M fitment. These look great.