|
|
|
02-26-2019, 02:21 PM | #1 |
Lieutenant
251
Rep 439
Posts |
Eccentric Shaft Sensor Opinions?
Hello,
Currently doing valve cover gasket(s) and was wondering if this is "enough oil" to consider replacing the sensor? Didn't really budget for it so thought i would check/ask here first since its very expensive.
__________________
2008 SGM 128i - 3 Stage IM - 130i Tune - Dinan Camber Plates - BMW PE - Injen Intake - 1M Mirrors - LCI Blacklines - M4 Spoiler - Blacked 263's - Aero Bumper - Aero Side Skirts - OMGSplitter - AFE Intake Scoops
|
02-26-2019, 06:55 PM | #2 |
Lieutenant
251
Rep 439
Posts |
Anyone?
__________________
2008 SGM 128i - 3 Stage IM - 130i Tune - Dinan Camber Plates - BMW PE - Injen Intake - 1M Mirrors - LCI Blacklines - M4 Spoiler - Blacked 263's - Aero Bumper - Aero Side Skirts - OMGSplitter - AFE Intake Scoops
|
Appreciate
0
|
02-26-2019, 08:11 PM | #3 |
Private First Class
37
Rep 131
Posts |
Just replace the gasket around it, and clean those nine teeth where the sensor connects. No need to change the sensor.
|
Appreciate
0
|
02-26-2019, 10:58 PM | #4 |
Lieutenant
251
Rep 439
Posts |
any best way to get the oil out?
__________________
2008 SGM 128i - 3 Stage IM - 130i Tune - Dinan Camber Plates - BMW PE - Injen Intake - 1M Mirrors - LCI Blacklines - M4 Spoiler - Blacked 263's - Aero Bumper - Aero Side Skirts - OMGSplitter - AFE Intake Scoops
|
Appreciate
0
|
02-27-2019, 02:45 PM | #5 |
Private First Class
37
Rep 131
Posts |
Good question lol. Most autoparts stores sell "electronics cleaner", you can try that. The only issue is that make sure you disconnect the car battery before spraying it, and make sure the engine is cold. you can use a lint free towel to do your best to clean around the teeth. |
Appreciate
0
|
02-27-2019, 02:47 PM | #6 | |
Lieutenant
251
Rep 439
Posts |
Quote:
__________________
2008 SGM 128i - 3 Stage IM - 130i Tune - Dinan Camber Plates - BMW PE - Injen Intake - 1M Mirrors - LCI Blacklines - M4 Spoiler - Blacked 263's - Aero Bumper - Aero Side Skirts - OMGSplitter - AFE Intake Scoops
|
|
Appreciate
0
|
02-27-2019, 06:36 PM | #7 |
Private First Class
37
Rep 131
Posts |
|
Appreciate
0
|
03-05-2019, 10:19 AM | #8 |
Lieutenant
251
Rep 439
Posts |
Had to get a new valve cover and its -20C so i haven't put it all back together yet. anyone used any SMP - products and would recommend? The sensor is only $300 as compared to BMW's $700
https://www.rockauto.com/en/moreinfo...76&jsn=3&jsn=3
__________________
2008 SGM 128i - 3 Stage IM - 130i Tune - Dinan Camber Plates - BMW PE - Injen Intake - 1M Mirrors - LCI Blacklines - M4 Spoiler - Blacked 263's - Aero Bumper - Aero Side Skirts - OMGSplitter - AFE Intake Scoops
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|