|
|
|
09-09-2017, 10:38 PM | #1 |
Enlisted Member
39
Rep 44
Posts |
Matt F's 128i Build Thread
Hey all,
This thread is to chronicle my build for my 2013 128i. Factory optioned she sits as follows: Mineral Grey / Black <45k miles 6 MT N51 Sunroof Leatherette heated seats Fog lights In my closet: Full SuperSprint exhaust (w/cat & resonator delete) ER competition oil cooler Completed Mods & Added Goodies: - OEM Side & Rear Sunshades - Ditched factory runflats for BFGoodrich G-Force COMP-2 A/S (@~42K) - Rear Seat Delete (9/10/17) - Including seat belts & seat latches. - AFE Air Scoops & BMS Cabin Intake Cowls (9/24/17) - CDV Delete & BMS Clutch Stop (11/19/17) - AFE Pro Dry Stage 2 Intake (11/26/17) Mods in progress: Next planned mod: ER Competition Oil Cooler Work planning: Ceramic coating headers (sourcing good local options) Glad to finally be introducing myself to the community, I'd like to thank so many of you for putting in the legwork on the front end and giving me the motivation to move forward. More to come soon. Cheers -Matt F Seattle, WA Last edited by MattF407; 11-26-2017 at 03:52 PM.. |
09-10-2017, 08:16 AM | #2 |
Bergspyder
1469
Rep 1,212
Posts |
Send that Burger CDV back and save your money. Disconnect lines from each side of CDV and the reconnect without CDV.
Even if you wanted a CDV body there (back when car was in warranty) you just push the guts of the valve out with a screw driver.. No one should spend money on a CDV and those that sell them should be ashamed of themselves. Great car and nice list of mods....get those M3 control arms on that list soon. Nice improvement.
__________________
|
Appreciate
1
desertman1232213.50 |
09-10-2017, 09:33 AM | #3 |
Lieutenant
96
Rep 406
Posts
Drives: S54/N52
Join Date: May 2014
Location: MA
|
Might want to mix suspension refresh into it.
Looking forward to hearing your thoughts on full SS header-exhaust setup! |
Appreciate
0
|
09-10-2017, 11:40 AM | #4 | |
Enlisted Member
39
Rep 44
Posts |
Quote:
Thanks for the recommendation on control arms, this is definitely on the list. It just so happened to be a sale + new financial situation that motivated the current purchase list. I will be looking at sourcing control arms and a few other suspension goodies around Dec - Feb, if things continue along this path. |
|
Appreciate
0
|
09-10-2017, 12:06 PM | #5 | |
Enlisted Member
39
Rep 44
Posts |
Quote:
My concern at this time is the combination of full exhaust & my rear seat delete, which already makes road noise & exhaust sound from the rear louder. I am looking into sound dampening in the trunk if it is too loud after the install. |
|
Appreciate
0
|
09-14-2017, 02:16 PM | #8 |
Joint Chiefs of Staff
24198
Rep 190,805
Posts |
__________________
Check out our current sale by clicking on this link!
https://x-ph.com/sale/ Phone number 702-494-9435 |
Appreciate
0
|
09-22-2017, 11:33 AM | #9 |
Sideways and Smiling
3027
Rep 2,860
Posts
Drives: In Exuberance
Join Date: Mar 2017
Location: Rosamond, CA USA
|
How's the rear seat delete affect noise in the cabin? Contemplating doing it myself, because race car.
__________________
2012 BMW 328i 6-Speed Wagon | Deep Sea Blue with Grey Dakota Leather | Manual Swap, 330i Intake + Tune, 3.15 Helical LSD, Öhlins R&T
(SOLD) 2009 BMW 128i 6-Speed Coupé | Monaco Blue with Black Sensatec | chris_flies' 128i thread |
Appreciate
0
|
09-23-2017, 02:40 PM | #10 |
!
698
Rep 3,267
Posts
Drives: 2010 128i
Join Date: Feb 2010
Location: Anacortes, WA
|
Why the rear seat delete? I mean, I guess I could see it if you were super competitive in autocross or something, and were looking for the last couple of tenths of a second to shave off, but even then there are a TON of more important things that need addressing (e.g., suspension). I suppose it is a free mod. What are your plans for the car?
Also, isn't that oil cooler for a 135i? I didn't think anyone made one for the N51/N52. Also not super important on a NA engine for typical street use, IMO. Are you going to alter it in some way to make it fit? There is also an OE oil cooler (it's very small) that was originally fitted to the 528i (I think), so if you have trouble installing that one you could always go for the OE option. Probably most sensible to do it in conjunction with a coolant and oil change.
__________________
____________________________ |
Appreciate
0
|
09-24-2017, 11:06 AM | #11 | |
Enlisted Member
39
Rep 44
Posts |
Quote:
In the end, if it becomes too much reinstall is still an option for you if you do not like it. Not every mod is for everyone. Hope this helps, and let me know if you have any questions along the way if you decide to move forward. |
|
Appreciate
0
|
09-24-2017, 12:13 PM | #12 | |
Enlisted Member
39
Rep 44
Posts |
Quote:
This mod is the start of a small design project I am beginning, one I have seen various interpretations of on the forum. I am working on mock ups for a rear cleanup panel(s), think a raised box like you might see in a Cayman. I am still in the infancy of this project, but I hope to have a rough visual prototype in the next month or so. So yes, free mod = fun project = I enjoy my days more. In the end, I could hate all of it and put the seats back in, but had a little fun along the way. I agree with all your points, I am not competitive, in fact me and the car have never seen track time. Also, without a doubt suspension mods would have some of the greatest impacts in improving this cars performance & handling on the track. My plans for the car will be staged over the next ~3-6 years. Stage 1: Power, Stage 2: Handling, Stage 3: Drivetrain, Seats, Exterior beautification. With some minor tracking and mountain driving along the way. Who knows though, my plans will change along the way. As for the oil cooler, this was a bit of research & a bit of praying it would work out without serious modification. I have the package waiting for me at fedex, and a decent amount of stuff waiting for me to get to first, but once I pick it up I will do some comparisons on the oil filter housings and check into mounting points for the coolers. AFAIK, oil filter housing should be direct bolt on, mounting coolers & lines may be of some issue, but I will tackle that challenge when I get there. I can report back if you are at all interested, and I appreciate the alternate you proposed from the 528i. I was reading a thread where I believe you and others discussed the use of this, but ultimately decided to go a more robust direction. My current fear on this mod is that I will have to replace my front bumper ahead of schedule to fit shrouding, or run without shrouding until i can source the bumper that I feel fits the car best. Thanks again for your input & interest, I'd be glad to talk further on any of these item! PS: Just realize you're in WA too! |
|
Appreciate
0
|
09-24-2017, 07:12 PM | #13 |
Enlisted Member
39
Rep 44
Posts |
Installed BMS intake Cowls & AFE air scoops today. Installs were easy. AFE scoops needed a T20 not a T25 like their manual reads. BMS intake cowls needed to remove the 3 cables that run across the front and slightly underneath the cowl before pulling it out (Instructions lack this direction).
Impressions, modest (~10-15%) increase in engine noise while driving. All in all worthwhile for the BMS intake cowls as the OEM was quite an obstruction. AFE scoops provide no noticeable difference to sound or performance, both as expected. They will however be a nice complement to my AFE intake when I install in a weekend or so. My biggest annoyance in the install is that you are left with 3 cables running over the top of your engine that the OEM cowl originally supported. A few zip ties later and I was a little happier with end results, though they still sag and touch at points. |
Appreciate
0
|
09-25-2017, 08:27 AM | #14 |
E82 Mudflap Ambassador
2214
Rep 2,219
Posts
Drives: '08 128i
Join Date: May 2016
Location: Orlando, FL
|
Where'd you manage to find those sunshades
Also would HIGHLY recommend the short shifter and ZHP knob
__________________
My 2008 128i - Sparkling Graphite/Beige - Sport pkg - 6MT - Click me!
Parents' 2014 528i - Mineral White/Ivory White - fully loaded Instagram @Andreys_128i and @Honda.Bito Last edited by desertman123; 09-25-2017 at 08:36 AM.. |
Appreciate
0
|
09-25-2017, 09:26 AM | #15 |
Enlisted Member
39
Rep 44
Posts |
Hey desertman123, ordered the set from BMW South Atlanta in about Feb of 2016. Best of luck finding a set, parking in a lot for work these and the sun visor really made life better in the Florida heat.
Thanks for the input on the shifter, I have hopes to squeeze this mod in as a Christmas present to myself along with some pedal covers, do you mean the OEM short? Or do you have any thoughts / recommendations on different products? I see TWM now produces but it's for the 135i and from my understanding the mounting and geometries are a bit different between the two models. Last edited by MattF407; 09-25-2017 at 11:24 AM.. |
Appreciate
1
desertman1232213.50 |
09-25-2017, 10:15 AM | #16 |
Brigadier General
3475
Rep 3,722
Posts |
Looking great MattF407! I like your efforts toward lightening the 128. They're definitely the best autox platform out of the 1ers IMO, even compared to the 135.
I noticed the oxy on your oil filter housing. Have you done checks for rust? You may want to have the underside/engine bay cleaned/steamed.
__________________
"Tobias" 2013 135i ///M-Sport 6MT • Pure Stage 1 • XDI 35 HPFP • 404whp/440wtq |
Appreciate
0
|
09-25-2017, 11:22 AM | #17 | |
Enlisted Member
39
Rep 44
Posts |
Quote:
Just figured out how to tag people in replies, hooray for learning... |
|
Appreciate
0
|
09-28-2017, 01:47 PM | #18 | ||
!
698
Rep 3,267
Posts
Drives: 2010 128i
Join Date: Feb 2010
Location: Anacortes, WA
|
Quote:
Quote:
Yeah man, anytime. If you have any questions along the way feel free to hit me up!
__________________
____________________________ |
||
Appreciate
0
|
11-23-2017, 02:38 PM | #19 |
Enlisted Member
39
Rep 44
Posts |
Knocked out my CDV delete & BMS clutch stop installs this past Sunday. So far I have only gone for 1 - 15 min drive after the CDV delete, & 1 - 30 min drive after the BMS clutch stop install.
Overall impressions: The CDV delete has improved pedal feel dramatically. The 'lag' so to speak in the pedal lifting and gummy depression feel non existent. This coupled with the reduced throw from the BMS clutch stops (I used all 3 shims) made shifting feel precise & effortless. Didnt snag any photos during the process, however both were quite easy to do. |
Appreciate
0
|
11-24-2017, 09:02 AM | #20 | |
E82 Mudflap Ambassador
2214
Rep 2,219
Posts
Drives: '08 128i
Join Date: May 2016
Location: Orlando, FL
|
Quote:
https://www.ecstuning.com/b-genuine-...r/25117542200/ https://www.ecstuning.com/b-genuine-...g/25111220600/ https://www.ecstuning.com/b-genuine-...p/25117571899/ https://www.ecstuning.com/b-genuine-...t/25117580281/ The actual shift lever is the only part you NEED, but while you're in there... I'm looking forward to seeing more of this build! The world needs enthusiastic 128i owners
__________________
My 2008 128i - Sparkling Graphite/Beige - Sport pkg - 6MT - Click me!
Parents' 2014 528i - Mineral White/Ivory White - fully loaded Instagram @Andreys_128i and @Honda.Bito |
|
Appreciate
0
|
11-26-2017, 04:03 PM | #21 |
Enlisted Member
39
Rep 44
Posts |
Installed AFE Stage 2 intake today with little to no problem, directions were poorly written however procedure was simple enough to not need much direction.
Overall impression: Thrilled... I took it out for a short drive after, I will update once I have driven it at higher speed & rpms. The sound difference is not noticable till about 2750+ rpm. Once there though, the sound begins to get quite throaty and deep & the pulls feel a decent bit stronger. Heres a few shots installed & of the detailed engine bay. |
Appreciate
0
|
11-26-2017, 04:49 PM | #22 | |
Bergspyder
1469
Rep 1,212
Posts |
Quote:
__________________
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|